Filter
Top Products
40 EN40 EN
3
Use [K / L] to enter the date, then
press [B].
Date
JAN/02
SP 2 : 00
Start
- - : - -
End
- - : - -
L1/L2
L1
REC To Mode
DVD SP
Daily
MON-SAT
JAN/01
JAN/31
MON-FRI
SAT
FRI
SUN
4
Use [K / L / { / B] or [the Number
buttons] to enter the start and end
time, then press [B].
Date
SP 2 : 00
Start End
- - : - -
L1/L2
L1
REC To Mode
DVD SP
JAN/02 1 : 00AM
• You cannot make a program whose recording
time exceeds 12 hours.
5
Use [K / L] to select an appropriate
external input (L1/L2) to which your
external tuner is connected, then
press [B].
Date
SP 1 : 00
Start End
L1/L2 REC To Mode
DVD SP
JAN/02 1 : 00AM 2 : 00AM
L1
6
Use [K / L] to select a recording media
(“DVD” or “VCR”), then press [B].
Date
SP 1 : 00
Start End
L1/L2 REC To Mode
SP
JAN/02 1 : 00AM 2 : 00AM
L1
DVD
7
Use [K / L] to select a recording
mode.
Date
SP 1 : 00
Start End
L1/L2 REC To Mode
JAN/02 1 : 00AM 2 : 00AM
L1
DVD SP
Refer to “Recording Mode” on page 34 for DVD
or “Recording” on page 100 for VCR.
• You can check the remaining recordable space
of the disc when you select the recording
mode.
Date
SP 1 : 00
Start End
L1/L2 REC To Mode
JAN/02 1 : 00AM 2 : 00AM
L1
DVD SP
Auto recording mode select (DVD only)...
When “Auto” is selected as a recording mode, the unit
calculates how much time is available on the disc and
determines the appropriate recording mode to
complete recording the program.
Date
Auto 1 : 00
Start End
L1/L2 REC To Mode
JAN/02 1 : 00AM 2 : 00AM
L1
DVD Auto
• “Auto” is only available for one program in the timer
program list.
• The recording may be cut short, when the available
recording space of the disc is too limited.
8
Press [ENTER] when all items are
entered.
After displaying an instructive message for 10
seconds, timer program list will appear.
Press TIMER SET for Timer Standby mode.
Ensure the external source is turned to
the correct channel.
When Timer set on DVD or VCR,
it is not available in the standby mode.
Press TIMER SET to cancel the Standby mode.
Timer Programming
THU JAN/01 10:00AMSP (1:00)
JAN/ 2/09 1:00 AM L1 SP
Date Start End L1/L2
JAN/02 1:00AM 2:00AM L1
Your program setting is stored.
• To set another program, repeat steps 2 to 7.
• To exit, press [TIMER PROG.] or [SETUP].
• When 2 or more programs are overlapped,
“Timer program overlapped” appears, and the
overlapped program will be displayed in blue.
To correct the timer program refer to
“Checking, canceling, or correcting the timer
programming information” on page 41.
9
Press [TIMER SET] to set a timer
programming.
will appear on the front panel display, while this
unit waits to make the recording.
CS DR CD
HDD
DVD
“VCR” will appear on the front panel display if VCR
timer recording have been set.
TIMER RECORDING
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
E9PKAUD_DVR620KU_EN.indd 40E9PKAUD_DVR620KU_EN.indd 40 3/25/2009 3:47:51 PM3/25/2009 3:47:51 PM