Filter
Top Products
25
HLV66 (E/F) Web 213:276
Chapter 5: Using the TV’s features
To open the Channel Browser
™
banner:
• Either… press 3 C, # c, or i on the remote control.
Or… press C to open the THINC menu, highlight
Channel Browser and press T.
• Press 3 C to surf backward through the previously tuned 32
channels or inputs in the History list, the channels in the
ANT 1 channel list, or the inputs in the Inputs list.
• Press # c to surf forward through the channel/input History,
the ANT 1 channel list, or the Inputs list.
Elements of the Channel Browser
™
banner
1 Input type
2 Highlighted item (channel or input)
3 Channels stored in the channel history
4 Instructions for programming the HOME key (this will be
replaced by the 6th item in the History list, ANT 1 list, or
Inputs list).
5 Current list (History, ANT 1 or Inputs)
6 Current input
7 Current antenna type (cable or TV)
8 Active channel number
9 Channel call letters (if available)
10 Resolution
11 Home source
To toggle among the History, ANT 1, and Inputs lists:
After opening the Channel Browser
™
banner, press B or b to
toggle between History, ANT 1 and Inputs.
Note: The Channel Browser
™
banner opens in History list by
default. Once another list has been selected, the
Channel Browser
™
will open in the last selected list.
To tune to a channel or input in Browse mode:
1 While watching TV, press 3 C or # c to open the
Channel Browser
™
banner and surf back to a previous
item or surf forward to the next item in the list.
In Browse mode, when you stop on an item in the
Browser banner, it will be highlighted and the TV will
automatically tune to the channel or input.
2 Press O to close the Channel Browser
™
banner.
Note: The Channel Browser
™
banner will close
automatically if you do not make a selection within 30
seconds.
To tune to a channel or input in Select mode:
1 While watching TV, press 3 C or # c to open the
Channel Browser
™
banner and surf back to a previous
item or surf forward to the next item in the list.
In Select mode, when you stop on an item in the browser
banner, it will be highlighted but the TV will not
automatically tune to the channel or input.
2 Press T to tune the TV to the highlighted item.
3 Press O to close the Channel Browser
™
banner.
Adding and clearing channels and inputs in the
channel history
Adding channels and inputs to the channel history:
As a channel or input is tuned, the Channel Browser
™
adds it
to the History and displays it on the “right side” of the Browser
banner. Previously tuned channels/inputs are “shifted” to the
left, eventually moving off the left side of the Browser banner.
Press 3 C to surf backward through the previously tuned
channels/inputs. Any channel or input that is tuned repeatedly
will not be repeated in the History, but instead is moved to the
top of the list on the right side of the Browser banner.
The Channel Browser
™
will store the following channels:
• All channels that are tuned using the numeric buttons on the
remote control.
• All channels that are tuned using < or ,, M or m on
the remote control.
• All inputs that are tuned to for at least 5 seconds.
Note: Whenever an item is selected that cannot be tuned (for
various reasons), the TV will automatically tune to the
previously viewed channel or input.
Clearing channels from the channel history:
• Reconfiguring the ANT 1 input will clear the channel
history.
Note: See page18 for details on configuring the antenna
input.
•
Once 32 channels or inputs are stored in the history list, the
oldest item will be removed from the list when a new
channel or input is tuned.
• Turning off the TV will clear the channel history only if
History List in the Channel Browser Setup is set to
“Power Off Clear (On).”
4
History
ANT 1 CABLE 4 AAA 480i
ANT 1(4)
Hold HOME key
3 sec to program
1 1
87-1
1
4-1
1
6
ClrStrmHD2
BLOCKED
__
5 678 9 10 11
1 23 4
263237HLV66_EN.book Page 25 Thursday, June 22, 2006 1:32 PM