Filter
Top Products
Operation
Vidikron Vision 50 Series Owner’s Operating Manual 45
PRE
L
IMINAR
Y
Figure 4-1. Vision 50 OSD Menu Structure
Service
White Balance
Gain
Red / Green / BlueOffset
Gamma
Save Color Temp. 4
Save Color Temp. 5
Gamma Selection
2.8, 2.5, 2.2, 1.0, 2.1, 2.15 or
2.7
ICC Adjust NTSC / HDTV / PAL
R / G / B / Y / C / M
Intensity / Sat. / Hue
Image Over Scan
Total 0, +1, +2, +3 ... +15
Horizontal
Vertical
Video Black Level 0 IRE or 7.5 IRE
Aperture Control 0, 1, 2 ... 19
Image Shift
Horizontal
-30, -29, ... 0 ... +29,
+30
Vertical
Amplitude
Horizontal
-60, -59 ... 0 ... +59,
+60
Vertical
Horizontal Masking 0, +1, +2, +3 ... +100
(Vision 50/CineWide
and Vision
50/CineWide with
AutoScope only)
Fan Control
Mode
Auto Normal,
Auto Hi. Altitude or
Manual
Fan Speed (Manual Mode)
Lamp Reset Timer Yes / No
RS-232 Baud Rate 9600, 38400 or 115200
Remote Control
Primary
Secondary
Screen Trigger Mode Normal or Trigger
(Vision 50/CineWide
and Vision
50/CineWide with
AutoScope only)
Return to User OSD
ISF
Calibration
Picture Adjust
Brightness, Contrast, Color
etc.
(see above)
White Balance Gamma, Gain, Offset etc. (see above)
Gamma Selection
2.8, 2.5, 2.2, 1.0, 2.1, 2.15
or 2.7
Aperture Control 0, 1, 2 ... 19
Blue Enable On / Off
Save ISF Settings ISF Night or ISF Day
Splash Screen Timer 5, 6, 7 ... 60 seconds
ISF Enable On / Off
Return to User OSD
Picture
Adjust
Brightness 0 ... 60
Contrast 0 ... 32
Color 0 ... 64
Tint 0 ... 30
Sharpness -14 ... 0 ... +25
Color Temp.
0, 1 (5400 K), 2 (6500K), 3
(8500 K), 4 or 5 (Custom)
Color Select
Standard, NTSC, HDTV or
PAL
Image
Option
Input Select
Video, S-Video,
Component 1,
Component 2, RGB-HD or
HDMI
Aspect Ratio
Anamorphic (16:9)
Standard (4:3)
Letterbox
IntelliWide
Cinema
Cinema Fill
(Vision 50/CineWide and
Vision 50/CineWide with
AutoScope only)
SD Enhance
H Enhance
0, 1, 2, 3 ... 127V Enhance
C (Chroma) Enhance
H Threshold
10, 11, 12, 13 ... 127V Threshold
C (Chroma) Threshold
Video Filter 0, 1, 2 or 3
HD/RGB Adjust
(480p and higher-res.
signals only)
Auto Adj.
Frequency 0, +1, +2, +3 ... +17
Phase 0, +1, +2, +3 ... +31
H. Position
-30, -29 ... 0 ... +29,
+30
V. Position
-28, -27 ... 0 ... +29,
+30
Blue Enable On / Off
Save Settings Custom 1
Load Saved Settings
Custom 1, ISF Night or
ISF Day
Projector
Status
Default
Sleep Timer 0, 10, 20, 30 ... 180 minutes
Lamp Power 250W or 200W
Lamp Hours (read-only)
Installation
Language
English, Français, Español,
Deutsch or Italiano
Picture Configuration
Floor Front, Floor Rear,
Ceiling Front or Ceiling Rear
Keystone -14, -13 ... 0 ... +13, +14
OSD Position Horizontal/Vertical
0/0 (lower left) ...
20/20 (upper right)
OSD Timer 0, 3, 6, 9 ... 60 seconds
PIP/PBP Setup
PIP/PBP Enable On / Off
PIP Set Up
PIP Off
Graphic in Video
Video in Graphic
PBP Set Up
PBP Off
Graphic by Video
Video by Graphic
Background Color Grey, Blue or White