Alpine DVA-9861 DVD Player User Manual


 
40-EN
01GB05DVA9861.fm
ALPINE DVA-9861 68-04123Z61-A (EN)
Setting Bass Compressor
You can adjust the sound of low frequencies as desired.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select the BASS SOUND mode by pressing MUTE.
4
Select BASS COMP. by pressing or , then
press MODE.
5
Select the desired mode by turning the
Rotary encoder.
Bass sound is emphasized more as the mode is
sequentially switched as COMP1 2 3, offering you
vivid low frequencies.
Select OFF when the setting is not necessary.
6
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
Setting Bass Focus
Using the previously specified delay number (time difference) allows
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With an
initial delay of 0.05 ms for each of the 0 to 400 steps, audible time
correction can be achieved.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select the BASS SOUND mode by pressing MUTE.
4
Select BASS FOCUS by pressing or , then
press MODE.
5
Press MODE to select the front/rear/left/right
speaker.
6
Turn the Rotary encoder to set the front/rear and
left/right speakers.
7
To set other channels (speakers), repeat steps 5 and
6.
8
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
Any setting in Bass Focus is applied in time correction, too.
When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 43.
Speaker Setup
The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if Decode mode is switched.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select the SP SETUP mode by pressing MUTE
repeatedly.
4
Select the speaker by pressing MODE.
5
Select the speaker characteristic by turning the
Rotary encoder.
6
Repeat steps 4 and 5 to set each speaker.
7
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
If the center speaker is turned “OFF,” the center channel’s audio
signals are added to the audio signals output from the front speakers.
If you set the speaker response to “OFF,” also set the speaker setting
to “OFF.” (page 36)
Perform the setup for all the speakers (“Front,” “Center,” “Rear”
and “Subwoofer”). If not, the sound may not be balanced.
When center is set to “OFF”, the setting is ineffective even if center
is set with this function.
Through changing the settings on each speaker, a change in the
output of the other speakers may occur due to the setting
requirements.
When using the PRO LOGIC II, if the rear speaker is set to
“LARGE”, then there will be no output from the subwoofer.
When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 43.
OFF*
1
: When no speaker is connected.
SMALL: When a speaker that cannot play low
frequencies (80 Hz or less) is connected.
LARGE*
2
: When a speaker that can play low frequencies
(80 Hz or less) is connected.
(Subwoofer is set to ON/OFF only)
*
1
It is not possible to set the front speakers to “OFF”.
*
2
If the front speakers are set to “SMALL”, the rear and
center speakers cannot be set to “LARGE”.
01GB00DVA9861.book Page 40 Tuesday, December 6, 2005 3:41 PM