41-EN
01GB05DVA9861.fm
ALPINE DVA-9861 68-04123Z61-A (EN)
Setting of Dolby Digital
The test tones help to make the volume adjustments of the different
speakers. When levels are equal, a strong sense of presence can be heard
from the different speakers at the listening position.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the decode mode is switched.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select the MULTI CH SETUP mode by pressing
MUTE repeatedly.
4
Select OUTPUT LEVEL by pressing or ,
then press MODE.
5
Press MODE to select the speaker to be adjusted.
The test tone is produced by the selected speaker.
6
Adjust the output level by turning the
Rotary encoder.
7
Adjust each volume level for optimum balance by
repeating steps 5 and 6.
• The adjustment range for the different speakers is –10 dB - +10 dB.
• Adjust based on the front speakers.
8
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
• If a speaker is set to off mode, that speaker’s level adjustment cannot
be made. Refer to “Speaker Setup” (page 40).
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 43.
This function mixes the front channel audio signals to the audio signals
output from the rear speakers, improving the sound in the vehicle’s rear
seat.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select the MULTI CH SETUP mode by pressing
MUTE repeatedly.
4
Select REAR MIX by pressing or , then
press MODE.
5
Select REAR MIX ON/OFF by turning the
Rotary encoder.
If ON is selected, press MODE.
If ON is set, the audio signal which is output from the rear
speaker is mixed to the front audio signal.
6
After setting to ON, turn the Rotary encoder to
adjust the level (LEVEL).
The level can adjusted in five steps: –6, –3, 0, +3 and +6.
The higher the level, the more bass is output from the rear
speakers. (The effect differs according to the software
(DVD, etc.).)
7
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
• This adjustment is ineffective when the rear speaker setup setting is
set to “OFF.”
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 43.
In most installations, the center speaker must be placed directly between
the front passenger and driver. Using this function, the center channel
information is distributed to the left and right speakers. This creates an
acoustic image simulating a center speaker directly in front of each
listener. Adjusting the center width in PL II MUSIC (see “Using the Pro
Logic II Mode” page 42), makes this function ineffective.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select the MULTI CH SETUP mode by pressing
MUTE repeatedly.
4
Select BI-PHANTOM by pressing or , then
press MODE.
5
Select BI-PHANTOM ON/OFF by turning the
Rotary encoder.
If ON is selected, press MODE.
If ON is set, the soundstage created is as if you are
positioned directly in front of the center speaker by
distributing the center speaker sound left and right.
6
After setting to ON, turn the Rotary encoder to
adjust the level (LEVEL).
The level can be adjusted within the range of –5 to +5. The
higher the level, the more the position of the center speaker
is shifted to the sides.
Adjusting the speaker levels
Mixing bass sound to the rear channel
Adjusting the acoustic image
01GB00DVA9861.book Page 41 Tuesday, December 6, 2005 3:41 PM