43-EN
01GB05DVA9861.fm
ALPINE DVA-9861 68-04123Z61-A (EN)
5
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
• This adjustment is effective when the setting of the center speaker is
SMALL or LARGE in the speaker setup settings.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if the Decode mode is switched.
• This adjustment is ineffective when the speaker is set to CENTER
“OFF” in “Setting the Speakers” (page 36).
• This function only works with two-channel signals. This operation is
ineffective when 5.1-channel DTS or Dolby Digital signals are input.
• If the setting of REAR FILL is made when REAR MIX is ON, sound is
unchanged in the rear fill setting because REAR MIX is given priority
during 2 channel decoder other than linear PCM.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 43.
Linear PCM Setting
The output when playing discs recorded in linear PCM can be set to 2 or
3 channels.
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Select PCM MODE by pressing MUTE repeatedly.
4
Select 2 CH or 3 CH by turning the Rotary encoder.
5
When the setting is complete, press and hold MUTE
for at least 2 seconds.
The unit returns to the normal mode.
• This adjustment is ineffective when the speaker is set to CENTER
“OFF” in “Setting the Speakers” (page 36).
Storing Settings in the Memory
Up to 6 set and adjusted contents can be stored on the unit.
All that are setting and adjusting items described below are stored in
one preset memory.
* Depending on the input signal, sound effect may not be obtained.
1
Adjust and set the value to be stored.
2
Press and hold for at least 2 seconds any one of the
preset buttons (1 through 6) into which you want
to store the set/adjusted value as preset memory
(MEMORY 1 through MEMORY 6).
• This function is operable only when Defeat is set to OFF.
• The stored contents will not be deleted even when battery power cord
is detached.
Recalling the Preset Memory
1
Check that Defeat mode is off (page 21).
2
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
3
Press any one of the buttons to select the preset
memory (MEMORY 1 through MEMORY 6) you want
to recall.
It takes a few moment to get out the preset memory.
Confirming the current Preset No./EQ
mode
1
Press and hold MUTE for at least 2 seconds.
The audio processor control mode is activated.
2
Press MUTE repeatedly to select PRESET INFO.
The current preset number and EQ mode appear in the
display.
Displays which EQ, graphic EQ or parametric EQ is
currently set.
G: Graphic EQ
P: Parametric EQ
3
Press and hold MUTE for at least 2 seconds to
complete confirmation.
The unit returns to normal mode.
2CH: 2ch output (L/R)
3CH: 3ch output (L/R/CENTER)
Setting/adjusting items Refer to page
Setting the Speakers 36
Setting Time Correction/Switching Phase/
Setting the Bass Focus
37, 38, 40
Adjusting EQ 38, 39
Adjusting X-OVER 37
Setting MX 36
Setting BASS COMP. 40
Setting PRO LOGIC II/Adjusting the Center
Width*
42
Adjusting Dolby Surround* 41, 42
Linear PCM Setting* 43
Preset No.
EQ setting display
is shown.
01GB00DVA9861.book Page 43 Tuesday, December 6, 2005 3:41 PM