Filter
Top Products
14
EN
I
NITIAL SETTING
BACK LIGHT
You can set the desired brightness mode.
(Refer to “Back Light Setting” on page 24.)
COLOR TEMP.
You can adjust color temperature.
(Refer to “Color Temperature” on page 24.)
DTVCC
In addition to the basic closed caption described
on page 21, DTV has its own closed caption called
DTVCC.
(Refer to “DTV Closed Caption” on page 22.)
PC SETTING
You can adjust the position, stability and clarity of the
PC screen.
This menu will appear only in PC mode, and can only
be set when the unit detects the PC input signal.
(Refer to “PC Settings” on page 28.)
Auto Channel Scan
If you switch wires (e.g., between antenna and CATV) or if you move the
unit to a di erent area after the initial setting, or if you restore the DTV
channel you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cables.
1
Press [SETUP] to display the main menu.
2
Use [Cursor K / L] to select “CHANNEL SETUP”,
then press [ENTER].
e.g.) digital TV mode
or
- TV SETUP -
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
3
Use [Cursor K / L] to select your desired preset type,
then press [ENTER].
e.g.) digital TV mode
or
- CHANNEL SETUP -
ADD/DELETE(DTV)
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
• When aerial antenna is connected,
select “AUTO PRESET CH(TV)”, “AUTO PRESET CH(DTV)”
or “AUTO PRESET CH(TV/DTV)”.
• When connected to CATV, select
“AUTO PRESET CH (CATV)”.
5
• Scanning and memorizing of channels start
automatically.
e.g.) digital TV mode
D25
AUTO PRESET CH(DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
• When you selected “AUTO PRESET CH(TV/DTV)”, the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed.
If there is no analog channel, the lowest memorized
digital channel will be displayed.
Note:
• After setting “Auto Channel Scan”, using [CH. K / L] on the
remote control skips unavailable programs automatically.
•
If you connect the cable system directly, contact the CATV
installer.
•
If you press [POWER] or [SETUP] during auto channel scan,
the setting will be canceled.
•
When no channel can be received by auto channel scan,
“NO TV SIGNALS” will be displayed on the TV screen.
•
Channel settings will be saved even if the power fails.
•
If you have Spanish or French menus and need English,
press [SETUP]. Use [Cursor K / L] to select “IDIOMA” or
“LANGAGE”. Press [ENTER] repeatedly to select “ENGLISH”.
Press [SETUP] to exit the main menu.
•
With regard only to the digital channel, even after the
scanning is completed if you unplug the AC power cord
before turning off the unit by pressing [POWER], the
channel setting may be lost.
Language Selection
You can choose English, Spanish or French as your on-screen language.
1
Press [SETUP] to display the main menu.
2
Use [Cursor K / L] to select “LANGUAGE”,
then press [ENTER] repeatedly to change the setting.
e.g.) digital TV mode
or
- TV SETUP -
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
ENGLISH
ESPAÑOL
FRANÇAIS
3
Press [SETUP] to exit.
5
A84N3UH_A84N1UH_LD195EM8 2_LD19514 14A84N3UH_A84N1UH_LD195EM8 2_LD19514 14 2008/02/15 14:31:162008/02/15 14:31:16