Filter
Top Products
2
2
1
1
–
12
–
EN
Setup
English
Preparation for Use
YES
NO
Hint
Hint
• To go back one step, press Cursor s
(during the steps [2] to [7].)
•
Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Hint
Hint
• If you accidentally select Spanish or
French but need English: Press MENU and
choose SELEC.IDIOMA, or
SELECTION LANGUE. Press
Cursor B, and select ENGLISH. Finally,
press CLEAR/C.RESET.
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section on page 7.
3
3
CH 01
AUTO SET UP
To Add or Delete Channels
1) Press MENU until the main menu
appears.
2) Select “CHANNEL SET UP” by
pressing Cursor K or L. Then, press
Cursor B.
3)
Select “MANUAL SET UP” by
pressing Cursor K or L. Then, press
Cursor B.
4) Enter the desired channel number by
pressing Cursor K or L.
5) Add or Delete it from memory by
pressing Cursor { or B. so that
“ADD” or “DELETE” flashes on the
TV screen accordingly.
6) Exit the preset mode by pressing
CLEAR/C.RESET.
To Preset the Channel Again
1) Press MENU until the main menu
appears.
2) Select “CHANNEL SET UP” by
pressing
Cursor K or L. Then, press
Cursor B.
3) Select “AUTO SET UP” by pressing
Cursor K or L. Then, press
Cursor B. After scanning, the tuner
stops on the lowest memorized
channel.
To Change the On-Screen Language
1) Press MENU until the main menu
appears.
2) Select “LANGUAGE SELECT” by
pressing Cursor K or L. Then, press
Cursor B.
3) Select “ENGLISH” , “FRANCAIS” or
“ESPAÑOL” by pressing Cursor K or
L. Then, press CLEAR/C.RESET.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
•
You can select only the channels memorized in
this unit by using SKIP/CH (i/K or j/L).
• If “AUTO SET UP” appears on the TV
screen again, check the cable connections.
Then, press Cursor B once again.
Y
Y
es
es Press MENU
to exit
• Refer to “Hint for Cable Box or
Satellite Box” section on page 7.
Do you connect the cable from the cable box or
the satellite box to the VCR/DVD’s ANT IN jack?
Turn on the unit for the first
time
Clock Set Up
To Select a Channel
You can select a channel by directly
entering channel using
the Number buttons on the remote
control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit channel
numbers with 0 (For example: 02, 03,
04 and so on).
5
5
4
4
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 5
HOUR MINUTE AM/PM
– – : – –– –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE AM/PM
0 5 : – –– –
6
6
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 – –
7
7
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
BPM
Select the current year
Select “AM” or “PM”
8
8 To exit the CLOCK SET
screen.
Select the current hour
Select the current minute
press first.
VCR
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
• If the clock is not set, the
CLOCK SET screen
appears when you press
MENU. In this case, go
to step [2].
press first.
VCR
*
Refer to page 11 to switch between the VCR/DVD modes.
To select the desired language
To decide
To decide
To decide
To decide
To decide
2
2
CLOCK SET
MONTH DAY YEAR
0 3 / – –– – – –
HOUR MINUTE AM/PM
– – : – –– –
3
3
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – –– –
Select the current month
Select the current day
To decide
To decide
or
or
or
or
or
or
or
or
or
CLEAR
C.RESET
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
H9850UD_EN/SP.qx3 05.4.8 11:42 AM Page 12