Filter
Top Products
Caution and Safety Instructions
Please read, understand and follow the warnings and instructions in this manual. Failure to do so can result in serious personal injury.
• Do not alter, modify or misuse the machine.
• Do not operate the machine using an ungrounded electrical system.
• Do not perform any maintenance on the machine unless both the electrical power and air supply are disconnected.
• Do not operate the machine in a damp, wet, gaseous, hazardous or poorly ventilated work environment.
• Do not obstruct any ventilation or air flow around the machine.
CAUTION – Hazardous parts inside, refer servicing to qualified service personnel.
CAUTION – Blade area can create high temperatures; refer servicing to qualified service personnel.
CAUTION – Use proper heavy lifting procedures.
Environmental Conditions
Indoor use only
Altitude up to 2,000m
Temperature 5°C to 40°C
Maximum relative humidity 80% for temperatures up to 31° decreasing linearly to 50% humidity at 40°C
Mains voltage fluctuations not to exceed±10% of normal voltage
Insulation Category II
Pollution degree 2
Unit can produce sound levels greater than 85 dB, proper hearing protection is required.
Warranty & Service Policy
Each unit is warranted to be free from defects in materials and workmanship under normal use and service for a period of 12 months after the date of
purchase. The obligations of IDEAL under this warranty shall be limited to repairing at the Sycamore, Illinois manufacturing facility any unit which
shall, within the 12 month period, be returned to us with the transportation charges prepaid, and with our examination shall disclosed to our satisfac-
tion to have been defective. This warranty shall not aply to any model which has been altered or repaired outside the factory in any way so as to affect
its operation nor which has been subject to misuse, negligence, accident or installed or operated in any other way than in accordance with our instruc-
tions, nor shall this warranty extend to repairs or replacement made necessary by the use of accessories not recommended by IDEAL.
Unpacking
The IDEAL Shielded Twisted Pair (STP) Cable Stripping System is shipped in
protective foam packaging. You may wish to save this packaging for future
transportation.
The STP unit is equipped with a power cord, air hose, slug tray, IDEAL T
®
-Cutter
Lite wire cutter, keys, key chain, air regulator kit and an operation manual.
Lifting Instructions for the STP
Locate the front and rear of the machine. The front of the machine has the keypad
and display. Position the machine so the front of the machine is pointing to your
left and the rear of the machine is to your right. Also position the machine as close
to your body as possible. Place your left hand underneath the bottom plate and
center it between the two front rubber feet. Place your right hand underneath the
bottom plate and center it between the two rear rubber feet. Pull the machine up and
toward your body. When carrying the STP, always keep the machine as close to your body as possible.
Note: Where ever possible, lift with your legs slightly bent and your back straight (vertical). Lift the load by straightening your legs not by pulling up
with your arms.
STP Service Setup (Qualified Service Personnel)
The STP front cover is secured with two (2) screws for shipping. Remove the
screws from lower right and left sides of cover before opening lid.
Gripper pad pins are secured with plates for shipping. Remove these plates
from both front and rear gripper pad housings before machine use.
NOTE: Do not invert the unit after shipping plates have been removed. Gripper
retaining pins will fall out when inverted.
Close cover and replace screws removed.
Install slug tray - Insert the long screws provided, tighten.
Description Cat. No.
STP, 115 VAC, 60 Hz 4A 45-930
STP, 230 VAC, 50 Hz 2A 45-935
Power Cord K-6773
T
®
-Cutter Lite 45-260
Air Hose K-6865
Slug Tray IA-3124
Air Regulator 45-906
Operation Manual ND-3514
Security keys 1301.012
IDEAL Key Chain 99-020
3
Front
Rear