Filter
Top Products
34
www.insigniaproducts.com
Checking the codes
If you have set up the remote using the procedure
in “Searching for your code” on page 33, you may
need to find out which five-digit code is operating
your equipment.
To find out which code is assigned to your TV
(for example):
1 Press TV once.
2 Press and hold SET until the red LED blinks
twice, then release.
3 Enter 9 9 0. The LED blinks twice.
4 To view the code for the first digit, press 1.
Count the red LED blinks (for example, three
blinks = 3), then write down the number in the
appropriate code listing at the top of this
column.
5 Repeat Step 4 for the four remaining digits,
using 2 for the second digit, 3 for the third digit,
4 for the fourth digit, and 5 for the fifth digit.
6 To check for other device codes, repeat Steps 1
through 5, substituting the device key for the
device you would like to check.
Using learning
This universal remote control includes a learning
feature (some models may not include this) so you
can add functions that are unique to your home
entertainment devices (such as VCR Tracking Up or
Down). However, there are some considerations to
keep in mind.
Precautions
• Your original remote controls must be in working
order for learning to work properly.
• Learned keys are mode-specific, so each one can
store a unique function for each mode.
• Do not use the following keys for learning: Device
Keys, SET, or (record).
• Learning capacity is approximately 42 to 75 keys,
depending on the code being learned.
• Certain device functions are not learnable,
including multi-frequency types, some high
frequency functions, and other unusual formats.
• For optimum learning, avoid high levels of
ambient light such as natural sunlight or
energy-efficient fluorescent lights.
Programming a learned key
To program a learned key:
1 Place your Insignia remote control
head-to-head (about 2" apart) from your
original remote control (the one that came with
the device). Also, locate the key (on your original
remote control) that you want the Insignia
remote control to learn. Press the mode key you
wish to learn functions on.
2 Press and hold SET until the LED blinks twice,
then release.
3 Enter 9 7 5. The LED blinks twice.
4 Press the key on the remote you wish to
program. The feedback LED stays lit for three
seconds, indicating that the remote is ready to
learn.
5 On the original remote, press and hold the key
to be learned. Continue holding the key on the
original remote until the Insignia’s LED blinks
twice.
6 Repeat Steps 4 and 5 to program another key.
Once you have completed programming all the
keys you want, press and hold SET until the LED
blinks twice to save all data learned.
Deleting a single learning key
This process returns the key to its original
programming for the mode you select. You can also
delete learned programming by teaching a
different function to the key (see “Programming a
Learned Key” above).
To delete a single learned key:
1 Press the mode key that you wish to remove the
learned key from.
2 Press and hold SET until the LED blinks twice,
then release.
3 Enter 9 7 6. The LED blinks twice.
4 Press the key containing the learned function to
be deleted, twice. The LED blinks twice and
programming ends.
Note
If the LED does not blink, the code digit is 0.
Note
Please have your original remote controls handy
before programming learning.
Note
If more than 10 seconds pass between key presses,
the remote exits programming.
If the LED displays one long flash instead, either
your batteries are low, or the Insignia remote
control has a memory fault. In either case, the
remote cannot learn a new key.
Note
If the red LED displays one long blink, a learning
error has occurred. Try repeating this step again
until a successful capture occurs. If the function is
still not captured, press and hold SET to exit
programming and review the Precautions” above.
If needed, also see “Troubleshooting remote
control programming” on page 37. After reviewing,
start programming again at Step 1.
Note
If more than 10 seconds pass between key presses,
the remote exits programming.
If the LED displays one long flash instead, either
your batteries are low, or the Insignia remote
control has a memory fault. In either case, the
remote cannot learn a new key.