Filter
Top Products
18
4 MENU SWITCHES
4-2 Menu switch details
For switch setting procedures, refer to
“Menu switch setting
procedure”.
q: Factory setting
(00): The number in the bracket shows the set value on the
counter display.
002 OPERATION LOCK
Details: Switches the operation lock ON/OFF.
Setting:
qOFF (00): The operation lock is OFF: all operations
are enabled.
ON (01): The operation lock is ON: all controls are
disabled except for the [MENU] button.
003 SYNC SELECT
Details: Selects the sync signal during play.
Setting:
EXTERNAL (01): Synchronizes with the signal input
to the [SYNC IN] connector.
qAUTO (03): Switches the synchronization
automatically depending on
whether or not a signal is input to
the [SYNC IN] connector. For
details, refer to page 11.
050 REMOTE SELECT
Details: Selects the remote controller connected to
the [REMOTE] connector on the rear panel.
When the optional SA-K46 RS-232C
interface board is installed at the [REMOTE 1]
connector, some setting indications will change.
Setting:
IEEE 1394 (01): Allows control of this unit with the
controller connected to the [DV IN/
OUT] connector.
RS422A (04): Allows control of this unit with the
controller connected to the
[REMOTE 1] connector.
IEEE 1394 + RS422A (05): Allows control of this
unit with the controllers connected
to the [DV IN/OUT] and [REMOTE 1]
connectors.
JVC BUS (08): Allows control of this unit with the
controller connected to the
[REMOTE 2] connector.
JVC BUS + IEEE 1394 (09): Allows control of this
unit with the controllers connected
to the [REMOTE 2] and [DV IN/
OUT] connectors.
JVC BUS + RS422A (12): Allows control of this unit
with the controllers connected to
the [REMOTE 2] and [REMOTE 1]
connectors.
qJVC BUS + RS422A + 1394 (13): Allows control of
this unit with the controllers
connected to the [REMOTE 2],
[REMOTE 1] and [DV IN/OUT]
connectors.
(When the optional SA-K46 RS-232C interface
board is installed)
IEEE 1394 (01):Allows control of this unit with the
controller connected to the [DV IN/
OUT] connector.
RS232C (02): Allows control of this unit with the
controller connected to the
[REMOTE 1] connector.
IEEE 1394 + RS232C (03): Allows control of this
unit with the controllers connected
to the [DV IN/OUT] and [REMOTE 1]
connectors.
JVC BUS (08): Allows control of this unit with the
controller connected to the
[REMOTE 2] connector.
JVC BUS + IEEE 1394 (09): Allows control of this
unit with the controllers connected
to the [REMOTE 2] and [DV IN/
OUT] connectors.
JVC BUS + RS232C (10): Allows control of this unit
with the controllers connected to
the [REMOTE 2] and [REMOTE 1]
connectors.
qJVC BUS + RS232C + 1394 (11): Allows control of
this unit with the controllers
connected to the [REMOTE 2],
[REMOTE 1] and [DV IN/OUT]
connectors.
108 VIDEO INPUT SELECT
Details: Selects the input video signal.
Setting:
qLINE (00): Selects video signals input to the
[LINE IN] connector.
Y/C (01): Selects video signals input to the
[Y/C IN] connector.
COMPONENT (02): Selects video signals
input to the [COMPONENT IN]
connector.
IEEE 1394 (03):Selects video and audio signals
input to the [DV IN/OUT]
connector. In this case, analog
audio signals are not input.
125 SETUP (U MODEL)
Details: Sets whether or not the setup is applied to
the analog video signals (composite, Y/C,
component).
Setting:
OFF (00):Does not apply the setup.
qON (01): Applies the setup. Set to this position to
play back a tape recorded on the GY-
DV500.
Notes:
• This setting affects recording and playback of
analog video signals.
• Picture hue and brightness can be affected if
dubbing is repeated without applying a setup
suitable to video signals.
For servicing
See the service manual page 1-19 “1.11 SET UP SW
”.
←
19
4 MENU SWITCHES
4-2 Menu switch details
q: Factory setting
(00): The number in the bracket shows the set value on the
counter display.
212 AUDIO OUT AT SEARCH
Details: Selects whether or not audio is output to the
[AUDIO OUT] and [AUDIO MONITOR OUT]
connectors and headphones jack during
search at speeds above ±1x.
Setting:
OFF (00):No output.
qON (01): Audio is output.
214 V. FADE
Details: Switches the V. fade function ON/OFF. V.fade
reduces audio noise at the tag recording
during playback.
Setting:
OFF (00):The V. fade function is not activated.
qON (01): Activates the V. fade function.
245 SAMPLING RATE
Details: Selects the sampling rate frequency when
recording audio digitally.
Setting:
32K (00): Records signals at a 32 kHz sampling
frequency. Set to this position for audio
dubbing on CH3 and CH4.
q48K (01): Records signals at a 48 kHz sampling
frequency. Audio dubbing is not possible
with this setting.
311 AUTO PLAY
Details: Selects whether or not playback starts
automatically after the tape is rewound to the
beginning.
Setting:
qSHORT FF (00): The tape stops after short FF.
Auto play does not start.
PLAY (01): Auto play starts. Repeat playback
is available when No. 312 <AUTO
REW> menu switch is set to
“ON”.
312 AUTO REW
Details: Selects whether or not the tape is rewound
automatically at tape end during recording or
playback.
Setting:
qOFF (00):The tape is not rewound automatically.
ON (01): The tape is rewound automatically.
Repeat playback is available when No.
311 <AUTO PLAY> menu switch is set to
“PLAY”.
353 EDIT ADJUST
Details: When this unit is used with an editing
controller and the edit-in point is shifted, this
corrects the play start timing.
Switch setting differs depending on the
configuration of the editing system. For
details, refer to
“Edit adjust setting
” on page 1
6.
Setting:
q0F: No compensation.
1F: The playback start point is delayed by 1 frame.
2F: The playback start point is delayed by 2 frames.
3F: The playback start point is delayed by 3 frames
to the factory set timing.
4F: The playback start point is delayed by 4 frames.
5F: The playback start point is delayed by 5 frames.
6F: The playback start point is delayed by 6 frames.
7F: The playback start point is delayed by 7 frames.
360 AUTO REW AT TIMER
Details: Selects whether or not the tape is automati-
cally rewound when the VCR power is
switched ON in the Timer Play or
Recording Standby mode.
Setting:
qOFF (00): Playback or recording starts immedi-
ately. The tape is not rewound.
ON (01): Playback or recording starts after the
tape is rewound to the beginning.
363 CONTROLLER SELECT
Details: Selects the setting according to the type of
remote control unit connected via the RS-
422A interface.
Setting:
qTYPE 1 (00): For the RM-G820.
TYPE 2 (01): For a non-linear editing system.
TYPE 3 (02): Unused.
:
TYPE 8 (07)
396 BATTERY SELECT
Details: When using DC power, set this switch
according to the DC power supply and
battery type.
Setting:
q12 V (00): Select this setting to use a DC power
supply (AA-G10) or DC 12 V flat shape
type battery.
13.2 V (01): Select this setting to use Anton Bauer
Inc.’s Trimpack 13, ProPac 13.
14.4 V (02): Select this setting to use Anton Bauer
Inc.’s Trimpack 14, ProPac 14 and IDX
Corporation's NP-L46.