Filter
Top Products
40
12 TROUBLESHOOTING
12-1 Warning indicators
If the unit malfunctions during operation, the built-in self-diagnostics system identifies the problem and displays a warning
message on the monitor and/or the counter display. Also, the [AUTO OFF] indicator may be shown on the LCD. In this case,
turn the power off and then on again to restore operation. If the [AUTO OFF] indicator appears again, the VCR may require
repair or adjustment. Consult your local JVC dealer.
The VCR’s built-in microprocessor is susceptible to interference from externally generated noise or electro-magnetism. In this
case, turn the main power (AC and DC power supplies) off, turn on again and check the operation.
On-screen display
Counter display
Error contents
Condensation on the drum.
Tape cannot be loaded.
• Tape cannot be
unloaded.
• Tape is jammed.
The eject operation is
abnormal.
The cassette housing is
abnormal.
The tape ends.
The tape is slack.
The tape end sensor is
abnormal.
The tape beginning sensor is
abnormal.
The drum rotation stops.
The capstan rotation stops.
Operation
• When a cassette is not
loaded, the drum starts to
rotate.
• When a cassette is loaded,
the AUTO OFF mode is
engaged and the operation
stops.
Operation stops. No
operations are possible.
Solution
Wait for the drum to stop
rotating, then load a
cassette.
Do not use the unit until the
AUTO OFF mode is
disengaged.
Turn the power on again. In
some cases, the tape may
be damaged, so use a
different tape. If the problem
persists, consult your JVC
dealer.
CONDENSATION ON DRUM
The [DEW] indicator
lights.
FAILURE LOADING
ERR3200
FAILURE UNLOADING
ERR3300
CASSETTE EJECT FAILURE
ERR4100
HOUSING FAILURE
ERR4200
TAPE DEFECTIVE
ERR5605
TAPE DEFECTIVE
ERR5607
END LEADER DETECTION
ERR5702
BEGIN LEADER DETECTION
ERR5802
DRUM MOTOR FAILURE
ERR7001
CAP MOTOR FAILURE
ERR7101
For servicing
See the service manual page 1-16 “1.7 WARNIGN CODES
”.
→
41
Solution
On-screen display
Counter display
Operation
Operation stops. No
operations are possible.
Operation stops. No
operations are possible.
Operation continues.
Operation stops.
Operation stops.
Operation stops.
Operation continues.
Operation stops.
Operation continues.
Operation stops about 60
seconds after the fan motor
stops (with the No. 397 <FAN
STOP SHUTDOWN> menu
switch set to “ENABLE”).
The operation continues.
12 TROUBLESHOOTING
Turn the power on again. In
some cases, the tape may
be damaged, so use a
different tape. If the problem
persists, consult your JVC
dealer.
Turn the power on again.
Use a tape recorded in the
SP mode.
Set the safety slide to
“REC”.
Copy-guarded signals cannot
be recorded.
Input signals to the [DV IN/
OUT] connector.
Copy-guarded signals cannot
be recorded.
When the IEEE 1394 input is
selected, the EE check
cannot be performed.
Set the safety slide to
“REC”.
Use a tape recorded at the
32 kHz sampling rate.
Set the No. 245 <SAMPLING
RATE> menu switch to
“32K”.
Audio dubbing cannot be
performed on tapes recorded
in the LP mode.
Use a tape on which SSF
data has been properly
recorded.
Consult your nearest JVC
dealer.
Clean with a dedicated head
cleaning tape. Refer to the
separate enclosure,
“Notes
on the use of a cleaning
tape”.
SUP REEL FAILURE
ERR7202~ 7203
TAKE UP REEL FAILURE
ERR7302~ 7303
SYSCON REF ERROR
ERR8400
PC TAPE INHIBIT
Pc7APE
LP INHIBIT
LPiNh
REC INHIBIT
REciNh
1394 INHIBIT
1394iNh
EE CHECK INHIBIT
EEiNh
AUDIO DUB INHIBIT
ADBiNh
SSF INHIBIT
SSFiNh
FAN MOTOR FAILURE
FAN STOP
HEAD CLOG
HEAD CLOG
The supply reel rotation is
abnormal.
The takeup reel rotation is
abnormal.
System controller reference
signal failure.
A data tape for personal
computer is used.
A tape recorded in the LP
mode is played back.
The cassette’s safety slide is
set to “SAVE”.
Copy-guarded signals are
input.
No signal is input to the [DV
IN/OUT] connector.
Copy-guarded signals are
input.
When the IEEE 1394 input is
selected, the EE check is
performed.
The cassette’s safety slide is
set to “SAVE”.
The tape was recorded with
the 48 kHz sampling rate.
The No. 245 <SAMPLING
RATE> menu switch is set to
“48K”.
Audio dubbing was attempted
on a tape recorded in the LP
mode.
SSF data error occurs.
The fan motor stops.
The video head is clogged.
Error contents
Use a tape on which NTSC
(U MODEL), PAL (E MODEL)
signals are recorded.