Filter
Top Products
Masterpage:Right+
EN 31
Filename [MV5S_08Basic TimerDub.fm]
TIMER RECORDING
Page 31Wednesday, 31 August 2005 16:55
You can programme each deck to timer-record as many as
8 programmes up to 30 days ahead.
If you do not know the S
HOWVIEW number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
NOTES:
● When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
● In case of a power failure after programming, the unit’s memory
backup keeps your selections for approximately 10 minutes.
● Programmes that start after midnight must have the next day’s date.
● To record the programmes received by the satellite receiver, record
on the DVD discs. For details, refer to “Satellite Receiver Users (DVD
Deck Only)” above.
1 Press DVD or VHS to select the deck on which you want to
perform timer programming.
2 For DVD deck
Load a recordable disc.
For VHS deck
Load a cassette with safety tab intact.
3 Press PROG to access the
Programme Check screen.
4 For DVD deck
Press rt w e to select “DVD”
and press rt to select “NEW
TIMER PROGRAMME”, then
press ENTER.
For VHS deck
Press rt w e to select “VHS”
and press rt to select “NEW
TIMER PROGRAMME”, then
press ENTER.
5 Press rt to set the desired
date.
● The current date appears on the
TV screen. The date you enter
appears in its place.
6 Press we to select “START”, then press rt to set the desired
start time.
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7 Press we to select “STOP”, then press rt to set the desired
stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8 Press we to select “TV PROG”, then press rt to select the
desired channel.
9 Press we to select the desired recording option as required.
● Refer to step 6 in “SHOWVIEW™ Timer Programming” (੬ pg. 29).
10 Press ENTER to access the Programme Confirmation screen.
11 Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 11.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 35.
12 Press TIMER # to engage the unit’s timer mode. The DVD
timer indicator lights up on the unit and the unit is automatically
turned off.
● To disengage the timer mode, press TIMER # again.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
Satellite Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Manual Timer Programming”.
B Set the satellite receiver to the appropriate channel before
the selected programme begins.
C Select “L-2” in step 8.
D Leave the satellite receiver’s power on.
rtwe
ENTER
DVD
VHS
TIMER
PROG
VHS DVD
19:00 - 20:00
22:00 - 22:30
13:30 - 14:00
16:00 - 17:00
PROG
++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++
DISC TIMER PRGM
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
OK
SELECT
EXIT
05/07 SAT
44 SP
10/07 THU
10 XP
11/07 FRI 26 LP
WEEKLY
11/07 FRI 33 LP
DATE
START-STOP
TV PROG VPS/PDC
REC MODE
DAILY/WEEKLY
ON
OFF
OFF
ON
LP
VTM 1020:3020:00
TIMER PROGRAMME
DATE
START
STOP TV PROG
05/07 SAT
DAILY/WEEKLY
VPS/PDC
OFF
NAME
SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]
REC MODE
CONFIRM
SELECT
PROG
EXIT
MV5S_00.book Page 31 Wednesday, August 31, 2005 4:55 PM