Filter
Top Products
Filename [MV5S_13Subsidiary.fm]
Masterpage:Left+
92 EN
TROUBLESHOOTING
Page 92Wednesday, 31 August 2005 16:55
Playback (VHS Deck)
● The VHS deck is not selected.
] Press VHS/DVD on the unit repeatedly or VHS on the remote
control so that the VHS lamp lights up on the unit.
● The tape is already fully rewound or fast-forwarded.
] Check the cassette.
● The TV receiver’s channel selector is not set to the AV mode.
] Set the TV to its AV mode.
● This is normal.
● The automatic tracking mode is engaged.
] Try manual tracking. (੬ pg. 60)
● The video heads may be dirty.
] Use a dry cleaning cassette, or consult your JVC dealer.
● The automatic tracking mode is engaged.
] Try manual tracking. (੬ pg. 60)
Recording (DVD Deck)
● The channel position does not correspond to that in the
receiving area.
] Set the correct channel position for the receiving broadcast.
(੬ pg. 85)
● No disc or a disc not being compatible with the unit is loaded.
] Load a recordable disc on the unit. (੬ pg. 6)
● The disc loaded is not formatted.
] Format the disc. (੬ pg. 89)
● A finalised DVD-R disc is loaded.
] Recording cannot be made on finalised discs. Load a recordable
disc on the unit.
● The disc is full or does not have enough space for the title to be
recorded.
] Clear unnecessary titles on the disc or load a blank disc.
(੬ pg. 67)
Recording (VHS Deck)
● The unit is in the Record Pause mode.
] Press 4 to resume recording.
● There is no cassette loaded, or the cassette loaded has had its
record safety tab removed.
] Insert a cassette, or using adhesive tape, cover the hole where
the tab was removed.
● “L-1”, “L-2” or “F-1” has been selected as the input mode.
] Set to the desired channel.
● The camcorder has not been properly connected.
] Confirm that the camcorder is properly connected.
● The input mode is not correct.
] Set the input mode to “F-1”.
● The end of the tape was reached during recording.
] The programme may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire programme.
Timer Recording (DVD Deck)
● No disc is loaded.
] Press TIMER # so that the DVD timer lamp lights off. Load a
recordable disc, then press TIMER # again.
● Date and time is not correct.
] Set date and time correctly. (੬ pg. 88)
● Timer recording is in progress.
] Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
● Date and time is not correct.
] Set date and time correctly. (੬ pg. 88)
● Date and time set on the unit is not correct.
] Set date and time correctly. (੬ pg. 88)
● The channel position does not correspond to that in the
receiving area.
] Set the correct channel position for the receiving broadcast.
(੬ pg. 85)
● The unit’s channel positions have been set incorrectly.
] Refer to “S
HOWVIEW
TM
System Setup” (੬ pg. 83) and reperform
the procedure.
The VHS deck cannot be operated.
The tape will not rewind or fast-forward.
The playback picture does not appear while the tape is running.
Noise appears during visual search.
Noise appears during normal playback.
The playback picture is blurred or interrupted while TV
broadcasts are clear or “USE CLEANING CASSETTE” message
appears on the screen.
Breaks are noticeable in Hi-Fi soundtrack.
The desired programme cannot be recorded.
Recording cannot be made.
During recording, the tape does not run. The VHS recording lamp
lights up on the unit.
Recording cannot be done.
TV broadcasts cannot be recorded.
Camcorder recording is not possible.
The tape is automatically stopped, and “[” on the front display
panel won’t stop blinking.
“NO DISC” appears on the front display panel.
Timer programming cannot be made.
Timer programming recording does not start.
SHOWVIEW Timer Programming cannot be made.
The SHOWVIEW system does not timer-record properly.
MV5S_00.book Page 92 Wednesday, August 31, 2005 4:55 PM