Filter
Top Products
47
12
45
3
6
8
0
7
9
CH
MENU
OK
NUMBER
NUMBER "9"
NUMBER "8"
TIMER
SET PROGRAM
INFORMATION
5
Press the appropriate NUMBER keys to set the date,
start/stop time and channel number. Press CH5
∞
or
TIME SCAN 5
∞
to set AM/PM and tape speed. Press
OK after AM/PM, channel number and tape speed
settings. The next setting that can be set begins flashing.
● Any information comprised of 1 digit (except the
channel number) should have a "0" entered before it.
● It is possible to set all information using the CH
5
∞ or
TIME SCAN
5
∞ button.
(In this case, press OK after each setting.) Do not use
the CH ∞ or TIME SCAN ∞ button to set the date.
● If you are using the Illumi-Guide feature, OK blinks
when the following buttons are lit: NUMBER keys
(0 – 9), TIME SCAN, CANCEL and MENU.
NOTES:
● To timer-record a program received with a cable box
or DSS receiver, directly enter the channel that the
cable box or the DSS receiver receives it on.
● If a DSS receiver is used, cable channels 100 to 199
cannot be timer-recorded. For timer-recording of
these channels, set the "DSS RECEIVER OUTPUT" to
"OFF". (੬ pg. 23)
**You can record selected programs at the same time
every weekday, or once a week. Before entering the
month, press NUMBER key “8” (DAILY) or “9”
(WEEKLY). Either "DAILY" or "WEEKLY" appears.
Press again and "DAILY" or "WEEKLY" disappears.
For weekly recording, the desired date for the day of
the week must be entered.
MAKE CORRECTIONS
6
To change any of the settings, press OK or TIME SCAN
™ £ until the item you want to change begins
blinking. Then set as in step 5.
● If you are using the Illumi-Guide feature, OK blinks
when the following buttons are lit: NUMBER keys
(0 – 9), TIME SCAN, CANCEL and MENU.
RETURN TO NORMAL
SCREEN
7
Press MENU as many times as necessary.
● Press just once to access the Auto Timer screen
(੬ pg. 49).
● If you are using the Illumi-Guide feature, all buttons
go out.
ENGAGE TIMER MODE
8
Press TIMER. The VCR turns off automatically.
EXAMPLE
If you program the VCR to timer
record a show on September 6
on channel 40 from 12:00 noon
to 1:00 PM in SP mode, the
screen will look like this:
PROGRAM 1
DATE 9/ 6 SUN
START 12:00 PM
STOP 1:00 PM
CHANNEL 40 SP
PRESS NUMBER KEY(0-9)
OR (
5
,∞), THEN (OK)
PRESS (MENU) TO END
8
••
•
•
••
••
•
•
•
MENU
CH
OK
TIME SCAN
NOTES:
●
To disengage the timer before recording starts, press TIMER
again. Pressing once more re-engages it.
●
In case of a power failure after programming, the VCR’s memory
backup keeps your selections for approximately 10 minutes.
●
If you select "PROGRAM SET" without having set the date and
time, an error message appears. Follow its instructions.
●
If you enter a start time that has already passed, "ERROR"
appears on the screen and flashes.
●
Programs that start after midnight must have the next day’s date.
●
After timer recording is completed, the VCR’s power goes off
automatically.
●
You can program the timer while a regular recording is in
progress; the on-screen menu will not be recorded.
●
If the end of tape is reached during timer recording, the
cassette is automatically ejected.
●
When timer-recording cable channels received through a
Cable Box, be sure to keep the Cable Box set to ON.
●
When timer-recording satellite channels received through a
DSS receiver, be sure to keep the DSS receiver set to ON.