Filter
Top Products
30
STATUS DISPLAY
CONTROL LOCK
REMOTE SWITCH
HD SIGNAL MODE
FAN SPEED
WHITE BALANCE
TIMER
SET-UP MENU 1/2
ADJUST:
SELECT:
EXIT:
MENU
: OFF
: OFF
: MODE1
: 1080i
: LOW
Other Convenient Functions (Continued)
3
Press 5/∞ to select the item you want
to set and set the item as follows.
REFRESH
You can activate/deactivate the function manually.
• Press 2/3 to select the desired setting.
ON: The function is activated immediately after
exiting the menu operations.
OFF: The function is deactivated.
TIMER: Select this when you use the Refresh On/Off
Timer.
Note:
• Set the clock (see page 26) and select “TIMER,” before
using the Refresh On/Off Timer.
START SET
You can activate/deactivate the Refresh On Timer.
• Press 2/3 to select “ON” or “OFF.”
ON: The function is automatically activated at the
time set in “START TIME.”
OFF: The Refresh On Timer is deactivated.
START TIME
You can adjust the time to activate the function.
• Set the hour and minute following steps 4 to 6 in
“Setting the Clock” (page 26).
END SET
You can activate/deactivate the Refresh Off Timer.
• Press 2/3 to select “ON” or “OFF.”
ON: The function is automatically deactivated at the
time set in “END TIME.”
OFF: The Refresh Off Timer is deactivated.
END TIME
You can adjust the time to deactivate the function.
• Set the hour and minute following steps 4 to 6 on
“Setting the Clock” (page 26).
4
Press MENU/EXIT (or MENU on the
Monitor) repeatedly to exit from the
menu operations.
To reset the Reflesh function setting
After step 2 above, proceed as follows:
1 Press 5/∞ to move the cursor (3) to “reset.”
2 Press 3.
The confirmation screen appears.
3 Press 3 again to reset the setting.
To cancel the reset, press MENU/EXIT (or MENU on the
Monitor).
Note:
• The Refresh function requires considerable time to reduce
the afterimage. Deactivate the function temporarily at
intervals of 30 minutes-1 hour and check the screen if the
afterimage still remains or not. Set the function to off if the
afterimage has been reduced.
Notes on the Color-Reverse/Refresh Timer
• Once you set the Color-Reverse/Refresh timer, the timer
function is still activated even if you turn off the power.
If you turn on the power after the “START TIME” you
set, Color-Reverse/Refresh function is activated.
To cancel the function, select “OFF” in the menu
(see pages 29 and 30).
• The Color-Reverse timer is deactivated when you turn
on or off the Color-Reverse function manually.
The Refresh timer works in the same way as mentioned
above.
Select “TIMER” in the menu to control the functions
automatically (see pages 29 and 30).
Resetting All the Setup Menu Settings
You can reset all the following Setup Menu settings at a time,
except the use time (HOUR METER).
1
On the remote control:
Press VOLUME – while holding MENU/
EXIT to display the Setup Menu.
On the Monitor:
Press 2 while holding MENU to display
the Setup Menu.
2
Press 5/∞ to move the cursor (3) to
“reset” (on the second page).
• The Setup Menu consists of two pages. If you keep
pressing 5/∞, you can move to the other page from
the current page.
Cursor (3)
PIXEL SHIFT
POWER SAVE
COLOR-REVERSE
REFRESH
reset
all reset
HOUR METER x100h
SET-UP MENU 2/2
ADJUST:
SELECT:
EXIT:
MENU
: OFF
: OFF
: 123
MODEL
:GM-X50 Ver. A
CATEGORY
. E
Are you sure?
"YES"
then key.
"NO" then key.
MENU
reset
22-31_GM_X50E.p65 04.3.14, 3:30 PM30