Filter
Top Products
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left+
20 EN
INITIAL SETTINGS
Page 20 Tuesday, 29 June 2004 17:40
Results Of Auto Set Up/Preset Download Appearing
On The Front Display Panel
If both Auto Channel Set and
Auto Clock Set have been
performed successfully, the
correct current time is displayed.
Turn on the TV and select its AV mode, then make sure that all
necessary stations have been stored in the unit’s memory by using
the PR +/– button(s).
● If station names (ID – ੬ pg. 85) have also been stored in the unit’s
memory, the station name will be displayed at the top right corner of
the TV screen for about 5 seconds when the unit is tuned to a
different station.
● If you want to set the tuner manually such as to add or skip channels,
to change channel positions, or to set or change station names, see
pages 71 – 72.
If Auto Channel Set has
succeeded but Auto Clock Set
has not, “PR 1” (channel
position) is displayed.
OR
If both Auto Channel Set and Auto Clock Set have failed,
“– –:––” is displayed.
A Turn on the TV and select its AV mode, then make sure that all
necessary stations have been stored in the unit’s memory by
using the PR +/– button(s).
● If station names (ID – ੬ pg. 85) have also been stored in the unit’s
memory, the station name will be displayed at the top right corner of
the TV screen for about 5 seconds when the unit is tuned to a
different station.
● If you want to set the tuner manually such as to add or skip channels,
to change channel positions, or to set or change station names, see
pages 71 – 72.
B Perform “Clock Set” on page 73.
A
TTENTION:
After making sure the cables are connected properly, turn off the unit’s
power once, then turn the unit’s power back on again.
The Country Set display appears on the TV screen; perform “Auto Set
Up” on page 18 or “Preset Download” on page 19 again.
IMPORTANT:
● To check if the Guide Program numbers have been set correctly,
perform the S
HOWVIEW Timer Programming. (੬ pg. 44)
● In certain reception conditions, station names may not be stored
correctly, and auto Guide Program Number Set may not work
properly. If the Guide Program numbers are not set properly when
you timer-record a TV programme using the S
HOWVIEW system, the
unit will record a TV programme of a different station. When
programming the timer using the S
HOWVIEW system, be sure to
check the desired channel is selected correctly. (
੬ pg. 44,
“ShowViewTM Timer Programming”)
● Your unit memorizes all detected stations even if reception of some of
them is poor. You can delete those stations with an unacceptable
picture. (
੬ pg. 72, “Delete A Channel”)
INFORMATION
Language for the on-screen display
Auto Set Up also selects the language automatically for the on-
screen display depending on the Country setting you have made in
step 2 on page 18 (unless you have selected BELGIUM or
SUISSE), as shown below.
If you want to change the language setting manually, see “On-
screen Language Set” on page 21.
Just Clock
Your unit is equipped with the Just Clock function which provides
accurate time keeping through automatic adjustments at regular
intervals, by reading data from a PDC signal. If you want to take
advantage of this function, simply set it to “ON”. (੬ pg. 73)
T-V Link Functions
When you connect the unit to your TV via a fully-wired 21-pin
SCART cable (੬ pg. 17), the following functions are available. You
can use these functions only with a TV offering T-V Link, etc.*
For details, refer to the instruction manual of your TV.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART
cable. The degree of compatibility and available functions may differ by
system.
TV Auto Power On
The TV will turn on and be set to its AV mode automatically
whenever you start playback.
For details, refer to the instruction manual of your TV.
Unit Auto Standby
You can use your TV’s remote control to turn off the unit.
For details, refer to the instruction manual of your TV.
Direct Rec
You can easily start recording the programme that you are
watching on your TV. When you use this function, set “DIRECT
REC” to “ON”. (੬ pg. 68)
SUOMI
]
SUOMI ITALIA
]
ITALIANO
PORTUGAL
]
ENGLISH MAGYARORSZÁG
]
ENGLISH
DEUTSCHLAND
]
DEUTSCH ESPAÑA
]
CASTELLANO
POLSKA
]
ENGLISH NEDERLAND
]
NEDERLANDS
NORGE
]
NORSK GREECE
]
ENGLISH
SVERIGE
]
SVENSKA
OTHER WESTERN
]
ENGLISH
DANMARK
]
DANSK
ÖSTERREICH
]
DEUTSCH
OTHER EASTERN
]
ENGLISH
Č
ESKÁ REPUBLIKA
]
ENGLISH
DR-MH30EU_00.book Page 20 Tuesday, June 29, 2004 5:41 PM