Filter
Top Products
Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Left0
44 EN
Page 44 Tuesday, 29 June 2004 17:40
TIMER RECORDING
You can programme this unit to timer-record as many as
32 programmes.
With the S
HOWVIEW system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognize.
You can use the remote control to enter the S
HOWVIEW number.
1 Load a recordable disc if recording to DVD.
2 Press PROGRAMME to access the programme top screen.
3 Press rtw e to select “SHOWVIEW”, then press ENTER.
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES” appears on the TV screen, you need to cancel
some of the reserved programmes. (
੬ pg. 47)
4 Press the number keys to
enter the S
HOWVIEW number of a
programme you wish to record.
OR
Press rt w e to select the
desired number key on the
screen, then press ENTER.
Repeat to enter all needed
numbers.
5 Press rt to select “RECORD TO”, then press ENTER. Press
rt to select the desired recording deck, then press ENTER.
6 Press rtw e to select “CONFIRM”, then press ENTER.
● If the number you entered is invalid, “SHOWVIEW NO. ERROR
CONFIRM SHOWVIEW NO. THEN RETRY” appears on the TV
screen. Input a valid S
HOWVIEW number.
● If “GUIDE PROGRAMME IS NOT SET SET GUIDE PROGRAM
THEN RETRY” appears on the TV screen, set Guide Program
Numbers manually. (
੬ pg. 70)
7 The SHOWVIEW number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
programme data.
● To cancel this setting, press RETURN.
8 Press rt to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “INPUT TITLE” (੬ pg. 50, “Modify Title Name”)
● “CATEGORY” (
੬ pg. 51, “Modify Category”)
● “VPS/PDC” (
੬ pg. 45, “VPS/PDC Recording”)
● “WEEKLY/DAILY” (
੬ pg. 45, “Weekly/Daily Recording”)
● “REC MODE” (
੬ pg. 35, “Recording Mode”)
9 Press rt to select “OK”, then press ENTER to access the
Programme Confirmation screen.
10 Press we to select “EXIT”, then press ENTER to complete
timer programming.
● To programme another timer, press we to select “CONTINUE”, then
press ENTER.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 47.
NOTES:
● There may be cases that SHOWVIEW Timer Programming function
prolongs the stop time of the programming.
● When two successive programmes are recorded on a DVD-RW disc
with S
HOWVIEW Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
SHOWVIEW
TM
Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
PROGRAMME
DISPLAY
CLEAR
0 – 9
VPS/PDC#
RETURN
ENTER
CANCEL
CABLE/SAT
DVDTV
PROGRAMME > SHOWVIEW (1/2)
SHOWVIEW NO.
PRESS [PROGRAMME]
TO EXIT
SELECT WITH [ ]
THEN PRESS [ENTER]
CONFIRM
RECORD TO
1234
12
456
789
0
DELETE
DELETE ALL
DVD
ENTER
SELECT
EXIT
PROGRAMME
3
1
2
3
1
2
2
3
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “ShowViewTM System Setup” (
੬ pg. 70) and
set the Guide Program number correctly.
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the S
HOWVIEW programme screen in step 7. When
this happens, set the correct Guide Program number for that station.
(
੬ pg. 70, “ShowViewTM System Setup”)
Satellite Receiver Users
To timer-record a satellite broadcast using the S
HOWVIEW
system:
A Perform “Satellite Receiver Control Setting” (੬ pg. 23).
B Perform “ShowViewTM Timer Programming” (੬ pg. 44).
C Leave the satellite receiver’s power on.
DR-MH30EU_00.book Page 44 Tuesday, June 29, 2004 5:41 PM