Filter
Top Products
Masterpage:Right+
EN 71
Filename [DR-MH30EU_10Subsidiary.fm]
SUBSIDIARY SETTINGS
Page 71 Tuesday, 29 June 2004 17:40
8 View the Confirmation screen.
“AUTO SET COMPLETED” or “SCAN COMPLETED” is displayed
on the TV screen.
9 Press SET UP to complete the setting.
● Using the Confirmation screen, you can skip or add channel
positions, enter station names and perform other operations. Refer to
pages 71 – 72 for the procedures.
● Depending on reception conditions, the stations may not be stored in
order, and the station names may not be stored correctly.
● For information on scrambled broadcasts, refer to “When Receiving A
Scrambled Broadcast” (
੬ pg. 72).
NOTES:
● Fine tuning is performed automatically during Auto Channel Set. If
you want to perform tuning manually, refer to “Fine-Tuning Channels
Already Stored” (
੬ pg. 72).
● If you perform Auto Channel Set when the aerial cable is not
connected properly, “SCAN COMPLETED –NO SIGNAL–” appears
on the TV screen in step 8. In such a case, make sure of the aerial
connection and press ENTER; Auto Channel Set will start again.
● If no sound accompanies the picture or the audio sounds unnatural
on some channels that have been stored by Auto Set Up, the TV
system setting for those channels may be incorrect. Select the
appropriate TV system for those channels. (
੬ pg. 72,
“INFORMATION”)
Manual Channel Set
Store channels that were not stored during Auto Set Up
(੬ pg. 18), Preset Download (੬ pg. 19) or Auto Channel Set
(੬ pg. 70).
1 Press SET UP to access the Main Menu screen.
2 Press we to select “INITIAL SET UP”, then press t.
3 Press we to select “TUNER SET”, then press t.
4 Press rt w e to select “MANUAL CH SET”, then press
ENTER. The Manual Channel Set screen appears.
5 Press we to select “EDIT”, then press ENTER.
6 Press rt w e to select a
blank position in which you want to
store a channel, then press
ENTER. The Confirmation screen
appears.
7 Press rt to select “BAND”,
then press ENTER.
8 Press rt to change the band
between CH (regular) and CC
(cable), then press ENTER.
9 Press rt to select “CH”, then
press ENTER.
10 Press rt to input the
channel number you want to store.
● To enter the registered station
name (
੬ pg. 85), press rt to
select “ID”, then press ENTER. Press rt.
● For fine tuning adjustment, press rt to select “FINE”, then press
ENTER. Press rt to perform fine-tuning.
● When storing a channel that sends scrambled broadcasts, press rt
to select “DECODER”, then press ENTER. Press rt to set
“DECODER” to “ON” (“OFF” is the default setting).
● When “L-2 SELECT” is set to “VIDEO”, “S-VIDEO”, “SAT VIDEO” or
“SAT S-VIDEO”, the “DECODER” setting cannot be changed.
(
੬ pg. 61)
11 Press ENTER to enter new channel information. The
Confirmation screen appears.
12 Press SET UP to close the Confirmation screen.
● To change positions, see “Change Station Channel Position”
(
੬ pg. 72).
● If you wish to set station names other than the ones registered in your
unit, see “Set Stations (B)” (
੬ pg. 72).
IMPORTANT:
● In certain reception conditions, station names may not be stored
correctly, and Auto Guide Program Number Set may not work
properly. When the Guide Program numbers are not set properly,
the programme that you do not intended to record will be timer-
recorded by the S
HOWVIEW system of the unit. When programming
the timer using the S
HOWVIEW system, be sure to check the
desired channel is selected correctly. (
੬ pg. 44, “ShowViewTM
Timer Programming”)
● Your unit memorises all receivable stations even if reception of
some of them is poor. You can delete those stations with an
unacceptable picture from the list. (
੬ pg. 72, “Delete A Channel”)
A
TTENTION:
Guide Program numbers are not set when channels are stored
manually. (੬ pg. 70, “ShowViewTM System Setup”)
CH ID CH CH ID
<>
MOVE EDIT RETURN
INITIAL SET UP > MANUAL CH SET
PR
01 C01 ----
02
02
CTEA
03 05 1000
04 C79 3SAT
05 01
9LIV
06
04
AB3
07 ----
08 ----
09 ----
10 ----
11 ----
12 ----
(Example) To store in position 12.
The programme currently
received on the selected channel
position appears behind the
confirmation screen.
PRESS [SET UP] TO EXIT
ENTER
SELECT
EXIT
SET UP
SELECT WITH [ ] THEN PRESS [ENTER]
INITIAL SET UP > MANUAL CH SET
CH
BAND
2
CH
ID ----
RETURN
FINE
DECODER OFF
DR-MH30EU_00.book Page 71 Tuesday, June 29, 2004 5:41 PM