Filter
Top Products
69
Setting the clock time
If you have performed Auto Setup (see page 13) or TV-
Linked Setup (see page 14), the clock is set automatically.
Set the clock manually in the following cases.
• When the clock time has not been set correctly by
Auto Setup, TV-Linked Setup, or Auto Channel Set.
• When the backup memory is expired.
• When you want to change Just Clock* setting yourself.
1
Press SET UP.
2
Press
3
or
2
to move
to “INITIAL SET UP,” then
press
∞
.
3
Press
3
or
2
to move
to “INITIAL SET,” then
press ENTER.
4
Press
∞
or
5
to move
to “CLOCK SET,” then press
ENTER.
The Clock Set screen appears.
5
Press
∞
or
5
to set the current time, then press
ENTER.
• If you hold
∞
or
5
, the time changes in 30-minute
intervals.
6
Press
∞
or
5
to set the date, then press ENTER.
• If you hold
∞
or
5
, the date changes in 15-day
intervals.
7
Press
∞
or
5
to set the year, then press ENTER.
8
Press
∞
or
5
to set Just Clock, then press ENTER.
• Each time you press
∞
or
5
, Just Clock turns “ON”
and “OFF” alternately.
9
Press
∞
or
5
to select the station from which you
receive the clock setting signal.
• Select the station transmitting the clock setting
signal—BBC1, BBC2,Channel 4, etc.
10
Press SET UP twice to finish the setting.
Setting the Guide Program number for
VIDEO P
LUS
+
®
System
Normally, Auto Setup (see page 13), TV-Linked Setup (see
page 14) or Auto Channel Set (see page 70) sets the
Guide Program numbers automatically.
Set the Guide Program numbers manually in the
following cases.
• When the VIDEO P
LUS
+
®
system cannot select the
correct programme position number for the station you
want to record.
• When you add a new station manually.
• When you want to record a satellite programme using
the VIDEO P
LUS
+
®
system (Set the Guide Program
numbers for all satellite broadcast stations which can
be received on your satellite receiver.)
Example: When inputting Guide Program number 4 for
CH4.
1
Press SET UP.
2
Press
3
or
2
to move
to “INITIAL SET UP,” then
press
∞
.
3
Press
3
or
2
to move
to “INITIAL SET,” then
press ENTER.
4
Press
∞
or
5
to move
to
“GUIDE PROG SET,” then
press ENTER.
5
Press
∞ or 5 to enter the
Guide Program number for
the desired station as
shown in the TV listings,
then press ENTER.
* Just Clock
Just Clock provides accurate time keeping through
automatic adjustments at regular intervals, by reading
data from a PDC signal. It also automatically adjust
the summer time setting.
• Just Clock adjusts the built-in clock every hour,
except for 23:00, 0:00, 1:00 and 2:00.
NOTES
Just Clock does not work in the following cases:
•When the unit is turned on.
•When the unit stands by for the timer recording or
Automatic Satellite Recording.
•When “L-2 SELECT” is set to “SAT.”
•When the built-in clock moves more than 3 minutes slower
or faster.
•When the signal reception is not good enough.
IMPORTANT: If you turn off Just Clock, the accuracy
of the built-in clock may be reduced, which could
adversely effect timer recording. It is recommended to
turn “ON” Just Clock. However, where the clock
setting data from a PDC signal is not accurate, turn
“OFF” Just Clock.
[ENTER]
[ENTER]
[SET UP]
[SET UP]
Guide programme number
“Guide programme (GUIDE PROG) number” refers to
the assigned TV station numbers in your area for the
VIDEO P
LUS+
®
system. The Guide Program numbers
can be found in most TV listings.
[ENTER]
[SET UP]