Magnavox 26MV402X CRT Television User Manual


  Open as PDF
of 55
 
English
32
Wirelessnetworksetting
This menu is displayed only when you set Wireless in
Networkselection. In order to use a wireless network, you must set up
a connection to the AP (e.g. wireless router).
3 Use ▲▼ to select Wirelessnetworksetting, then press OK.
Auto
Search for wireless networks automatically and select the SSID from the
list.
4 Use ▲▼ to select Auto, then press OK.
5 The list of wireless networks will be displayed.
Use ▲▼ to select the appropriate the SSID, then press OK.
Auto Router 1
Enter Key
Manually enter your S
Router 2
Select
Router 3
Enter Key
Router 4
Select
• If you select the SSID with , WEP*
2
/ WPA / WPA2 Key entry
screen will appear.
Enter the WEP*
2
/ WPA / WPA2 key of the selected wireless
network using ▲▼◄►, then press OK.
• If you select the SSID has a WPS, the WPS setting screen will
appear.
Use ▲▼◄► to select a setting, then press OK.
Simpleconnect
Select this setting if your router has a WPS
button. Start scanning for wireless networks on
the TV after pressing the WPS button on your
router. If connection test fails, try Simple connect
again.*
1
If it fails then refer to the router’s manual for
more details.
WPScode
Select this setting if your router has a WPS but
does not have a WPS button. Enter the 8-digit
WPS PIN code shown on your TV in the router
settings menu via PC before Connect is selected.
Manual
If your wireless network with authentication
setting (WEP*
2
, WPA-PSK or WPA2-PSK),
WEP*
2
/ WPA / WPA2 Key entry screen will
appear. Enter the WEP*
2
/ WPA / WPA2 key of
the selected wireless network using ▲▼◄►,
then press OK.
*1 WPS (Simple connect) cannot be used when the security protocol is set to
WEP. Change the Access Point’s security mode from WEP to WPA or WPA2
(recommended).
*2 WEP is not recommended to be used due to its Major security aws.
Change the Security protocol on the wireless router to WPA or WPA2
(recommended) mode.
Conrmation message will appear. Select OK to complete the settings.
Note
• For a wireless network with authentication setting, key icon appears to the right hand
of the SSID.
• Signal icon shows the strength of the signal.
• WEP*
2
/ WPA key appears as asterisks on the conrmation screen.
• The wireless LAN supports following specications.
– Wireless standards : IEEE 802.11 b/g/n
– Frequency spectrum : 2.4GHz
– Security protocol : WEP*
2
/ WPA / WPA2
ManuallyenteryourSSID
Set up the connection to the AP (e.g. wireless router) manually by
entering the SSID.
4 Use ▲▼ to select ManuallyenteryourSSID, then press OK.
• AP (e.g. wireless router) SSID entry screen will appear.
Enter the SSID using ▲▼◄►, then press OK.
5 Use ▲▼ to select the authentication setting of the selected
wireless network.
• For a wireless network with authentication setting, select the
authentication setting, according to the security type of the
wireless network.
Selectsecuritytypefor
"Router1"
None
WEP
WPA-PSK
WPA2-PSK
Back
None
Set the authentication setting to None.
WEP*
2
Set the authentication setting to WEP.*
2
WPA-PSK
Set the authentication setting to WPA-PSK.
WPA2-PSK
Set the authentication setting to WPA2-PSK.
• For a wireless network without authentication setting, select
None.
• If you selectWEP*
2
, WPA-PSK or WPA2-PSK, WEP*
2
/
WPA / WPA2 Key entry screen will appear.
Enter the WEP*
2
/ WPA / WPA2 key of the selected wireless
network using ▲▼◄►, then press OK.
• Conrmation message will appear. Select Yes to complete the
settings.
*
2 WEP is not recommended to be used due to its Major security aws.
Change the Security protocol on the wireless router to WPA or WPA2
(recommended) mode.
Continued on next page.
 previous next