Filter
Top Products
26
Setting Up VCR Plus+ (cont'd)
Now, compare the channel numbers
you have written into the GUIDE CH.
and USER CH. columns. You'll notice
that some stations have guide and user
channel numbers that are the same, and
other stations have channel numbers
that do not match. Where the channel
numbers DO NOT match, you must
tell the VCR the guide and user chan-
nel numbers according to the steps
below.
3
Press the MENU button, then press the
Number 2 button to select VCR SET UP.
SELECT PUSHNO.SHOWN_"_
ORMALPLAY ON ]
REPEATPLAY J
ON SCREEN MODE J
LANGUAGE |
GUIDE CHANNELSET |
GUIDE CHANNELMAP ]
END PUSH MENU j
4
Press the Number 5 button to select
GUIDE CHANNEL SET.
f'- GUIDE CHANNELSET
SELECTGUIDE CH. NO.
J
GUIDE CH,_ L%
USERCH._L_
END PUSH MENU
5
Look at the boxes you filled in on
pages 24 - 25. For stations whose guide
channels and user channels are not the
same, press two Number buttons for
the guide channel and two Number
buttons for the user channel.
• Always enter "0" before any single
digit channels.
• If you select line input for the user
channel, press 0, 0. AUX will appear
on-screen.
_- UIDECHANNELSET 1
SELECT USER CH. NO.
GUIDE CH.
USERC.._-_.÷
\ TOCORRECTPUSHCLEAR
"_T,,.OENDPUSHMENU
Press the Number 1button so your
VCR will memorize the guide channel
and user channel numbers you have
selected. Or, press the Number 2 but-
ton to quit and select another pair of
numbers.
Ii GUIDE CHANNELSET _N_
SELECT PUSH.NUMBER/
GUIDE CH. 28 [
USERCH. 04 /
1 MEMORIZE J
2 SELECTANOTHER CH. |
/
CORRECT PUSHCLEAR ]
END PUSH MENU _'
7
Repeat steps 5 and 6 for all the stations
on your list which have different guide
channel and user channel numbers.
8
Press the MENU button to exit.
9
To confirm the guide channel and user
channel numbers you have selected,
press the MENU button to bring up the
main menu display. Then press the
Number 2 button to select VCR SET
UP. Finally, press the Number 6 button
to select GUIDE CHANNEL MAP. A
list of guide channel and user channel
numbers memorized by the VCR will
appear on-screen. If there are more
than ten pairs of numbers, press the
Number 1button to view another
screen of numbers. Make sure these
numbers correspond to the boxes you
filled in in step 1. Then press the
MENU button to exit.
I
UIDE : USERGUIDE: USER J
0t :AUX C_:(_ J
03:OG 04:04 J
23:06 06:06 l
07:07 91:08 J
09:09 10:10 /
TOCANCB_PUSHO.EAR]
NEXT=I END=MENUJ
Number--
Buttons
• To correct a guide channel number:
1. Repeat steps 3 - 6 on this page.
2. At step 5, enter the incorrect guide
channel number for both the guide
channel and the user channel. This
will erase the incorrect guide channel.
3. Repeat steps 3 - 6 again, this time
entering the correct guide channel
and user channel.
• To correct a user channel number:
1. Repeat steps 3 - 6 on this page.
2. At step 5, enter the correct guide
channel and user channel mimbers.
• To cancel a pair of numbers:
1. Follow step 9 to display the guide
channel map.
2. Press the CLEAR button. A pair of
numbers will flash.
3. Press the CHANNEL (Up/Down) but-
tons until the pair of numbers you
wish to cancel is flashing.
4. Press the CLEAR button again. The
pair of numbers that was flashing will
disappear.
5. Press the MENU button to exit.