Filter
Top Products
27
Timer Recording With VCR Plus-"
oeeeoe eoeoll oeoooe eooee oeoo eeee •ioel• Io• eee eeooe*ol•eoloeleoeee• • • • •
Remote Control Read steps 1-7 to program a timer
POWER
Button
O
00000
750 oo
PLUS+/
ENTER
Button
Button
Button
Number-
Buttons
• If CODE ERROR appears at step 2
after you enter the VCR Plus+ number,
the number you entered was incorrect
(for example, too short). If this hap-
pens, press the CLEAR button to clear
the number, then enter the correct
number.
• CLASH m_yflash on the screen at step
2. This means that the timer recording
you just programmed and another
tim,er recording overlap, and thus the
current timer recording will not be
carried out.
• To quit VCR Plus+ programming at
any step, press the MENU button. The
on-screen display will disappear from
the TV screen.
• If the preset time for a timer recording
comes up during an OTR, the OTR has
priority.
• To stop a started timer recording, press
the STOP/EJECT button on the VCR.
• If the power fails for more than one
minute, programmed timer recordings
may be lost. If this case, repeat the
steps on pages seven and ten before re-
programming the timer recordings.
recording using VCR Plus+ numbers.
Before you begin make sure:
• Channels have been programmed.
• The clock has been set.
• There is a tape in the VCR (make
sure the tape's record tab is intact
andthe tape is long enough to record
the program(s).
• The VCR is in VCR position.
• You have selected CABLE TV or
TV at the TUNER SET UP menu.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
See page 37for more notes.
1
Press the VCR PLUS+/ENTER button
on the remote control. The on-screen
display shown below will appear.
_RPLu_PRO_.1
PwsCOOE_';-_:-
X_. END PUSH MENU
2
Press the Number buttons for the VCR
Plus+ number of the program you wish
to record (this number is different for
every program, and it can be fourto
eight digits long). Finally, press the
VCR PLUS+/ENTER button.
_oRP,0_P_O_.1
PkUSCODE:I_-..--
TOSETPUSH VCR +
• TOCORRECT PUSH CLEAR
END PUSH MENU
3
To record the program once, press the
Number 1button to select ONCE. To
• record the same program every day from
Monday through Friday, press the
Number 2 button to select DAILY. To
record the same program every week on
the same day (such as every Saturday),
press the Number 3 button to select
W'I_F,KT
4
Press the Number 1 button to record in
SP speed, press the Number 2 button to
record in LP speed, or press the
Number 3 button to record in SLP
speed. For details, see page five. You
cannot use the (Tape) SPEED button at
this time.
_'_
MEON 10:30PM
EOFF 1'_:30PU
ti_n_b_'l_" "_E_
END_ MENU
5
Press the MENU button. PROGRAM
WAS COMPLETED / PLEASE TURN
OFF VCR FOR TIMER RECORDING
should appear on the screen. After
three seconds, the on-screen display -
will disappear.
6
If needed, press the VCR PLUS+/ENTER
button and repeat steps 2 to 5. When you
are finished, go to step 7.
The VCR
must be off for a
timer recording
to take place!
7
Turn off the VCR power. The Timer
light will appear. The VCR must be
turned off for a timer recording to
take place. If you forget to turn the
VCR off, PLEASE TURN OFF VCR
FOR TIMER RECORDING flashes
on your TV screen two minutes before
a timer recording starts. You can
remove it by pressing the CLEAR but-
ton.
1