Mitsubishi Electronics LT-52153 Flat Panel Television User Manual


  Open as PDF
of 94
 
1. Basic Setup and Operation 13
About Auto Input Sensing/
Auto Output Sensing
ThisTV’sEasyConnect™AutoSensingfeature
detectsmostconnectionsautomatically.
Auto Sensing for Most Devices
Whenyoufirstconnectadevice,theTVwill:
a. Detecttheconnecteddeviceandautomatically
switchtoit.
b. Promptyoutoidentifythedevicetype.
c. 153 Series.PromptyoutoperformNetCommand
set-upforthedevice,ifavailable.
d. Repeatthesestepsforanyothernewlydetected
devices.
Which Jacks Trigger Auto Sensing?
TV Jacks and
Auto Sensing
Auto
Sensing
No Auto
Sensing
Y/VIDEO
(detectedascompositevideo)
Y/VIDEO
plus
Pb
(detectedas
componentvideo)
HDMI
USB
DIGITAL AUDIO OUTPUT
(orangejack)
AVR AUDIO OUTPUT
(
redjack)
SUBWOOFER OUTPUT
(blackjack)
DIGITAL AUDIO INPUT
(orangejack)
ANT
(Antenna)
IR NetCommand Output/External Con-
troller Input
(153series)
TheTVmaynotdetectanHDMIdevicewhen
thedeviceispoweredoff
.Detectionofthe
devicewilloccurthenexttimeitispoweredon.
When You First Connect a Device
Most Device Types.•
Selectthedevicetypefrom
theon-screenlist.Thedevicetypeyouselecthere
willappearasadeviceiconinthe
Activitymenu.
A/V Receiver•
TheTVdetectsaudioconnectionsonthe- DIGITAL
AUDIO OUTPUTjackandtheright(red)AVR
AUDIO OUTPUTjack.
ForanHDMIA/Vreceiver,select- AVRfromthe
listofdevicetypesiftheA/Vreceiverisnot
recognizedautomatically.
HDMI CEC Devices Compatible with the •
TV’s HDMI Control Feature.
CompatibleCEC-
enabledHDMIdevicesareoftenrecognizedauto-
maticallybytheTV.
HDMIControlmayallowyou
tocontrolsomefunctionsofaCEC-enableddevice.
SeeAppendixC,“HDMIControlofCECDevices.”
New Device
Found screen
for a device with
HDMI control
enabled. Select
On to enable
the TV’s CEC
control of the device. In some
cases, as in the example above,
you will also be prompted to select a device name.
Tips on Auto Sensing
Chooseadifferentnameforeachinput.•
Theantennainput(•
ANT
)isneverdetected,
althoughyoucanturnofftheunusedantenna
inputintheInputs>Namemenu.
Changethedevicetypedisplayedinthe• Activity
menuintheInputs > Namemenu(page47).You
mustswitchtoadifferentinputbeforechanging
thedevicetype.
153 Series.• Any“learned”NetCommandIRcodes
willbeerasedifyouchangethedevicetypeinthe
Inputs > Namemenu.
Reactivating Auto Sensing for an HDMI Input
WhenyoudisconnectanHDMIdevice,AutoSensingis
disableduntilyouperformthesesteps.
Switchtoanyinputotherthantheonetobedis-1.
connected.
DisconnecttheHDMIdevice.2.
DeletetheremovedHDMIdeviceinthe3. Inputs>
Namemenu(see“RemovinganHDMIDevice,”
page76).
ConnectthenewHDMIdeviceandthe4. New
Device Foundscreenwilldisplay.
Setting Up TV Inputs, continued
 previous next