Mitsubishi Electronics LT-52153 Flat Panel Television User Manual


  Open as PDF
of 94
 
68 Appendices
Programming the Remote Control
Pressthesidebuttonontheremotecontrolto
1.
changetothecorrectmodefortheproductyou
wanttocontrol.Refertothetablebelow.Only
oneofeachdevicetypecanbecontrolledineach
mode.
Mode Affected Device
CABLE/SAT
CableBox
DTVReceiver
SatelliteReceiver
VCR
VCR
DVR
DVDPlayer/Recorder
DVD
DVDPlayer/Recorder
DVR
VCR
AUDIO
A/VReceiver
AudioAmplifier
CDPlayer
Pressandhold
2.
POWER
ontheremotecontrolfor
severalsecondsuntilthemodeindicatorblinks
twiceandgoesoff.
Releasethe
3.
POWER
key.
Enterthefirstfive-digitcodelistedforyourequip-
4.
ment.
Themodeindicatorblinkstwicewhenyou•
starttoenterthecodeandthenonceforeach
additionalkeypress.
Themodeindicatorblinkstwicewhenyoufinish•
enteringavalidcode.
Ifyouneedtostartoverorwishtoexitpro-•
grammingmode,temporarilychangetoa
differentmodeusingthesidebutton.
Pointtheremotecontrolattheequipmentand
5.
press
POWER
.Iftheproducthasnopoweron/off
function,pressadifferentkey,suchas (
PLAY
),
(
STOP
),
VOLUME UP
,or
MUTE.
Iftheequipmentresponds,theremotecontrol•
isproperlyprogrammed.
Iftheequipmentdoesnotrespond,repeat•
steps2–4withthenextfive-digitcodelistedfor
yourequipment.
Onceyouhavefoundthecorrectcode,writeitin
6.
thespacebelowforfuturereference.
Mode
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
Todeterminethecodeprogrammedforanymode:
Setthemodetotheoneyouwishtoverify.
1.
Pressandhold
2.
POWER
ontheremotecontrolfor
severalsecondsuntilthe
modeindicator
blinkstwice
andgoesoff.
Presskeys
3.
9 9 0
Press
4.
1
andcounttheblinksofthepowerkey.
Writedownthenumberofblinksasthefirstdigitof
thecode.
Repeatstep4forthesecond,third,fourth,andfifth
5.
digitsofthecode.
Audio Lock: Universal A/V
Receiver Control
WithAudioLockenabled,theremotecontroloperates
volumeandmuteontheA/Vreceiverinallmodessetby
thesidebutton.ActivateAudioLockifyounormallyuse
anA/VreceiverwithyourTVandotherA/Vequipment.
Program
1.
AUDIO
modeforyourA/Vreceiveras
describedin“ProgrammingtheRemoteControl”on
thispage.
Withtheremotecontrolin
2.
AUDIO
mode,hold
POWER
ontheremotecontrolforseveralsecondsuntilthe
modeindicatorblinkstwiceandgoesoff.
Presskeys
3.
9 9 3 ENTER
ThemodeindicatorwillblinktwicetoindicateAudio
Lockisactive.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
Pressandhold
1.
POWER
forseveralsecondsuntilthe
modeindicatorblinkstwiceandgoesoff.
Presskeys
2.
9 9 3 VOLUME UP
.
Themodeindicatorwillblinkfourtimestoindicate
AudioLockhascleared.
Appendix B: Programming the Remote Control, continued
 previous next