Mitsubishi Electronics LT-52153 Flat Panel Television User Manual


  Open as PDF
of 94
 
60 6. NetCommand Control of an A/V Receiver
Automatic Switching (Audio or Audio/Video)
ThefollowingsetupsenabletheA/Vreceivertoswitch
automaticallytothecorrectinputwhenyouselecta
deviceintheTV’sActivitymenu.
Threedifferentconnectionarrangementsaredescribed
here.Reviewthedescriptionstofindthesetupneeded
foryourequipment.
To hear digital surround sound from a source device
you must use the setup described for Case 2
.
TosetupcontrolofanA/Vreceiveryouneed:
TheremotecontrolsfortheTVandA/Vreceiver.•
AnIRemittercableavailablefromMitsubishi.•
Connectingcables•
IMPORTANT
All audio from what you are watching on the TV is
always available from both the TV’s AVR AUDIO
OUTPUT and DIGITAL AUDIO OUTPUT jacks.
To use the digital surround sound capabilities of
your A/V receiver however, you must connect the
audio output from your DVD player, satellite receiver,
or cable box directly to the A/V receiver.
Before You Begin
ConnectyourA/VdevicestotheTVandconnect
1.
yourA/VreceivertotheaudiooutputsontheTV
andtheDVDplayer.Notethenameofthedevice
connectedtoeachA/Vreceiverinput.Seeinitial
setup,page12,and“TVConnections,”page16.
PositionNetCommandIRemittersasdescribedin
2.
“IREmitterPlacement,”page53.
SettheTV’sremotecontrolto
3.
TV
modeusingthe
sidebutton.
Openthe
4.
Inputs>AVRmenu,highlightNEXT
andpress
ENTER
todisplaythedevice-key-learning
menu.
Case 1: Automatic A/V Receiver
Switching to the TV Audio Input
MostdevicesaresetuptousetheTV’saudiooutputlike
theVCRinthisexample;analogaudiofromthedeviceis
sentthroughtheTVtotheA/Vreceiver’sTVaudioinput.
Usethissetupfor:
Analog Stereo Audio. •
Audiofromsourceswithonly
analogstereooutput(suchasaVCR)canbesenteither
directlytotheA/VreceiverorthroughtheTVfirst.
Mitsubishirecommendsyousendaudiothroughthe
TVasshownintheexample.TheTVconvertsanalog
audiotodigitalformattosendtoadigitalA/Vreceiver.
Setting Up A/V Receiver Control, continued
Audio Available from TV only. • Sendaudiofrom
the
ANT
inputtotheA/VreceiverfromtheTV’s
analogordigitalaudiooutput.
UsethissetuptomaketheA/Vreceiverswitchtoits
designatedTVaudioinputwhenviewingprogramming
fromthe
ANT
input.
HDMI Digital Stereo Audio. • Digitalstereoaudio
fromanHDMIconnectionisavailablebothindigital
andanalogformatfromtheTV’sanaloganddigital
audiooutputjacks.
TV
audio + video
Incoming Coaxial Cable
to TV’s ANT input
A/V Receiver
TV audio input
TV audio
out
audio output from
TV (digital or analog)
video
analog audio
VCR with
Analog Audio Output
Important:
Tousethissetup,youmustconnecttheTV’s
audiooutputtotheA/Vreceiver’sTVaudioinputjack.
Inthe
1.
Inputs > AVRmenu,press tohighlight
TV audio outastheA/Vreceiverinputtocontrol.
Press
2.
ENTER
ontheTV’sremotecontrol.
Whilethetext
3.
TV audio outisflashing,pressand
holdthe
TV INPUT
keyontheA/V receiver’sremote
control.
Whenacheckappearsnextto
4.
TV audio out,
releasethe
TV INPUT
key.
Ifthetextstopsflashingbeforethecheckmark•
appears,repeatthisstep.
ToerasetheIRcodejust“learned,”press•
CANCEL
whilethenameishighlighted.
Press
5.
MENU
iffinishedorcontinuewithCase2setup
ifyouwanttocontrolsurroundsoundswitchingfor
anotheraudiosource.
Case 1: NetCommand setup for controlling A/V
receiver switching to the A/V receiver’s audio input
from the TV
.
The list displayed represents inputs in use.
The device names are those you assigned in the New
Device Found screen or in the Inputs > Name menu.
 previous next