Filter
Top Products
30 4. TV Operation and Features
Note: To operate other audio/video devices using
the TV’s remote control:
• See Appendix D, “Programming the Remote
Control.”
• See chapter 6, “NetCommand,” for NetCommand
IR “Learning” of device keys.
• For HDMI devices compatible with the
TV’s NetCommand for HDMI feature, see
“NetCommand for HDMI Devices“ on this page.
23.
F1–F4
For devices under NetCommand control:
Perform NetCommand “Learning” to assign your
choice of functions to the
F1
–
F4
keys.
For devices operating independently of
NetCommand: The
F1
–
F4
keys work like the A, B,
C, D keys on some cable boxes, satellite receivers,
and DVD players. Program the remote control for
your equipment and test the keys. See Appendix D,
“Programming the Remote Control.”
25. (
PAUSE
): Freezes a broadcast TV picture.
Record/Playback Keys
Use any of these methods to enable the recording and
playback commands:
• Program the remote control for your DVR, VCR, or
DVD player/recorder and set the slide switch to
VCR
,
DVD
,
CABLE/SAT
, or
AUDIO
as appropriate.
• Perform NetCommand IR “learning” for the device.
• Check HDMI devices for compatibility with the TV’s
NetCommand for HDMI feature.
24.
(
RECORD
):
Records with a VCR or DVR.
25. (
PAUSE
): Pauses a VCR, DVR, or DVD. See
above for use during TV viewing.
26.
(
STOP
): Stops play of a VCR, DVR, or DVD.
27.
(
REVERSE
): Rewinds a VCR. Reverse scans a
DVR or DVD.
28. (
PLAY
): Plays a VCR, DVR, or DVD.
29.
(
FORWARD
): Fast forwards a VCR. Forward
scans a DVR or DVD.
Remote Control, continued
Care of the Remote Control
• Use only alkaline batteries.
• Be within 20 feet of the equipment.
• Do not press two or more keys at the same time
unless instructed to do so.
• Do not allow unit to get wet or become heated.
• Avoid dropping on hard surfaces.
• Do not use harsh chemicals to clean. Use only a
soft, lightly moistened cloth.
• Do not mix old and new batteries.
Resetting the Remote Control
If the slide switch is set to
TV
and the TV does not
respond properly, reset the remote control.
1. Press and hold
POWER
for several seconds until the
key blinks twice and goes off.
2. Release the
POWER
key.
3. Press keys
0 0 9 3 5
and the
POWER
key will blink
twice when you finish entering the code. While
entering the code, pause for a moment between
each key press to ensure it is recognized.
Low-Battery Indicator
If you press a key and the
POWER
key blinks five times,
replace the remote control’s batteries.
NetCommand for HDMI Devices
The TV’s remote may operate some functions of
compatible HDMI devices able to receive commands
through the HDMI cable. Test your equipment with the
TV’s remote to find out which commands are sup-
ported. See below for commands that may be avail-
able, depending on the individual device. You can add
commands using NetCommand IR “learning” after con-
necting and placing IR emitters for the devices.
Press
PLAY
on the device itself to:
• Turn on the TV if not already on
• Switch to the device (no need to display the Input
Selection menu)
• Begin play of the device
VCR, DVD, and DVR functions that may be available:
Record/
Playback
Menu
Navigation
Channel Tuning Other
CH
/
GUIDE
ENTER
Digits
0–9
,
—
CANCEL
F1
(content)
—
CANCEL
(to cancel)
ENTER MENU