Filter
Top Products
17
Speaker Setup
FM MODE
STANDBY/ON
STANDBY
POWER
PHONES
OFF
ON
TUNING/PRESET
SURROUNDSTEREO
T – D
DISPLAY
DVD / CD
PRESET
MEMORY
SUBWOOFER
MODE
SPEAKER
SETUP
SPEAKER
A / B
ACOUSTIC
CONTROL
INPUT
MASTER VOLUME
Setting up the Speaker Configuration
SPEAKER
SETUP
Display SPEAKER
SETUP
* See “To Listen to a High-Frequency/High-Quantization Format
Source in its Original Sound Quality – 96k Sound” on page 46.
I
N
P
U
T
S
E
L
E
C
T
O
R
M
O
D
E
A
U
D
I
O
D
V
D
T
V
T
A
/
M
D
L
I
S
T
E
N
I
N
G
M
O
D
E
A
.
C
T
R
L
T
–
D
S
T
E
R
E
O
S
U
R
R
T
I
T
L
E
M
E
N
U
S
E
T
U
P
T
V
/
V
C
R
R
E
T
U
R
N
CH
TUN
VOLENTER
REPEAT MUTING
A – B
REC
DIMMER
OPEN/CLOSE
RANDOM SLOW
SUBTITLE – ON / OFF
ANGLE ZOOM
MEMORYCLEAR AUDIO DISPLAY
--
/
---
SW MODE
LATE NIGHTDISTANCE
CH SEL
T– D SETUP
UP/ DOWN
TEST TONE
SP A
SP B
123
456
789
+
10 0
SEARCH
S
T
N
B
Y
O
N
S
L
E
E
P
A
U
D
I
O
Unit
Remote controller
SUBWOOFER
MODE
SW MODE
1
Before operating the
remote controller
Press MODE AUDIO.
The remote controller
remains in the AUDIO mode,
until another MODE button is
pressed.
→
Setting the Subwoofer Mode
Press SUBWOOFER MODE on the
unit or SW MODE on the remote
controller.
With the first press of the button, you can
check the present setting. Then each press
of the button changes the subwoofer mode
as follows (a tip on how to select the right
subwoofer mode is in parentheses):
SW Mode 2
(When large–wideband–front speakers
are connected)
↓
SW Off
(When no subwoofer is connected)
↓
SW Mode 1
(When small–with limited bass signal
handling–front speakers are
connected)
The normal display resumes in three
seconds.
SUBWOOFER
MODE
SW MODE
→
Selecting the number of speaker channels
Press SPEAKER SETUP repeatedly
to select the number of channels
for the SPEAKERS A system.
With the first press of the button, you can
check the present setting. Then each press
of the button changes the number of
channels as follows (the corresponding
speaker configuration is described in
parentheses):
Speaker 2
ch
(Front left and right speakers)
↓
Speaker 3ch
(Front left, center, and right speakers)
↓
Speaker 4ch
(Front left and right, plus surround left
and right speakers)
↓
Speaker 5
ch
(Front left, center, and right, plus
surround left and right speakers)
Note
The listening mode will automatically be set to
“Stereo” (see page 36) once you set or reset the
number of channels.
The normal display resumes in three
seconds.
Notes
• Speaker setup cannot be done if;
– Headphones are connected (see page 31), or
– The SPEAKERS B system is On (see page 30).
• It is not necessary to set the parameters again once you have
completed the setup (with one exception*) unless you change the
speaker configuration.
You need to set up the speaker configuration for the
speaker system connected to the SPEAKERS A
connectors (see page 13.)
(There is no speaker configuration setup for the
SPEAKERS B system.)
Unit only