Filter
Top Products
27
RQT8745
Messages
The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and
use.
On the television Page
On the unit’s display
The messages are alternately displayed.
Disc handling
Clean discs
Wipe with a damp cloth and then wipe dry.
Disc handling precautions
Do not attach labels or stickers to discs (This may cause disc
warping, rendering it unusable).
Do not write on the label side with a ball-point pen or other writing
instrument.
Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
Do not use scratch-proof protectors or covers.
Do not use the following discs:
– Discs with exposed adhesive from removed stickers or labels
(rented discs etc).
– Discs that are badly warped or cracked.
–Irregularly shaped discs, such as heart shapes.
Maintenance
Clean this unit with a soft, dry cloth
Never use alcohol, paint thinner or benzine to clean this unit.
Before using chemically treated cloth, read the instructions that
came with the cloth carefully.
Cleaning of the lens is generally not necessary.
Do not use any lens cleaners as they may damage the unit.
Cannot play. You inserted an incompatible disc (Discs recorded in PAL video, etc.). 4, 5
Cannot display on this unit. You tried to play a non-compatible image. 5
Copyrighted material. Audio
will not be output from HDMI.
Should you connect equipment that does not support HDCP the audio from the CPPM
copy protected DVD-Audio cannot be output from HDMI AV OUT terminal. Connect the
audio cable of the Audio/Video cable (Red, White), optical digital audio cable
or coaxial
cable
to the corresponding terminals.
8–10
No disc The disc may be upside down. —
The operation is prohibited by the unit or disc. —
F99 The unit fails to operate properly. Press [/I POWER] on the main unit to switch the unit to
standby. Now press [/I POWER] on the main unit again to turn the unit on.
—
HDMI ONLY
Some BD-Video discs can only be output with HDMI. —
No PLAY When there is a viewing restriction on a BD-Video or DVD-Video. 21
No READ The disc is dirty or badly scratched. The unit cannot play. —
PLEASE WAIT
Displayed when the unit is started and turned off. This is not a malfunction.
The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE
WAIT” is displayed.
—
—
SET
(“” stands for a number.)
The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [ENTER] and the indicated number button at the
same time for more than 2 seconds.
11
UNFORMAT
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or DVD-
RW (DVD-Video format).
—
UNSUPPORT
You have inserted a disc the unit cannot play. 4, 5
U59 The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling
fan on the rear of the unit.
—
U71 The connected equipment is not HDMI compatible. —
U72
U73
The HDMI connection acts unusually.
–The connected equipment is not HDMI compatible.
–Please use HDMI cables that have the HDMI logo (as shown on the cover).
–The HDMI cable is damaged.
—
H
or F
There is something unusual. (The service number displayed after H and F depends on the
unit’s condition.)
Check the unit using the troubleshooting guide. If the service number does not
disappear, do the following.
1. Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.
2. Press [/I POWER] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request service from
the dealer. Inform the dealer of the service number when requesting service.
—
24–26
D
R
Reference Messages / Disc handling / Maintenance
Reference