Filter
Top Products
28
RQT9184
(ENG)
“TV/Device Connection”
TV Aspect
Set to match the type of television connected.
When connected to a 4:3 aspect television:
≥4:3 Pan & Scan: Video recorded for a widescreen is played as Pan & Scan
(unless prohibited by the producer of the disc). When playing
BD-Video, video is output as “4:3 Letterbox”.
≥4:3 Letterbox: Video recorded for a widescreen is played in the letterbox
style.
When connected to a 16:9 widescreen television:
≥16:9
: Video recorded for 4:3 aspect screen is displayed as a 4:3
ratio image in the center of the screen.
≥16:9 Full: Video recorded for 4:3 aspect screen is displayed as a
horizontally stretched 16:9 image.
HDMI Connection
≥Press [OK] to show the following settings.
HDMI Video Mode
Select “On” when video is output from HDMI AV OUT
terminal.
≥On
: Images are output from the HDMI terminal in the resolution set in “HDMI
Resolution”. Video from COMPONENT VIDEO OUT terminal is output as
“480i”.
≥Off Images are output in the resolution set in “Component Video Resolution”.
HDMI Resolution
The items supported by the connected devices are
indicated on the screen as “¢”. When any item without
“¢” is selected, the images may be distorted.
≥Auto
: Automatically selects the output resolution best suited to the
connected television (1080p, 1080i, 720p or 480p).
≥480p ≥720p
≥1080i ≥1080p
–When the unit is connected to an amplifier/receiver that does not support the
resolution set on the unit, the video cannot be output properly. In this case, use
the HDMI cable to connect the unit to the TV and then connect the unit to the
amplifier/receiver using a cable other than HDMI.
–To enjoy high definition video up-converted to 1080p, you need to connect the
unit directly to 1080p compatible HDTV (High Definition Television). If this unit is
connected to an HDTV through other equipment, it must also be 1080p
compatible.
24p Output [BD-V] [DVD-V]
When this unit is connected to a TV supporting 1080/24p
output via an HDMI cable, this unit displays each frame at
1/24 second intervals – the same interval originally shot
with the film camera.
≥When playing DVD-Video, set to “On” and then set “24p”
in “Video” (> 25) to “On”
≥On: Images in 24p are output in 24p as they are.
However,
–when video is being output at 24 frames, images from any other
terminal than the HDMI terminal may not be output properly.
–[BD-V]: when images other than 24p are played, images are output at
60p.
≥Off
HDMI RGB Output Range
Effective when connected to a device that only supports
RGB output.
≥Standard: The video is output as it is.
≥Enhanced: When the black and white contrast of a video is low, the signal
is enhanced to reproduce clear video.
HDMI Audio Output
This setting selects whether or not to output audio from
HDMI.
≥On
:
≥Off: When the TV is connected to this unit using an HDMI cable, and this unit
is also connected to other devices, such as an amplifier/receiver using an
optical digital audio cable or a coaxial cable.
VIERA Link
Set to use “HDAVI Control” function when connected with
an HDMI cable to a device that supports “HDAVI Control”.
≥On
:
≥Off: Select when you do not want to use “HDAVI Control”.
Component Video Resolution
This sets the video output resolution when using the
component video terminal.
≥480i
≥480p ≥720p ≥1080i
Even if you select “720p” or “1080i”, the video output resolution is restricted to
“480p” when images of DVD-Video discs are output from the COMPONENT
VIDEO OUT terminals.
Speaker
You can set the unit to output the best possible sound for
your speakers.
≥Multi Channel
: When using 3 or more speakers. (> 29)
≥2 Channel: When using two speakers.
2ch down-mix audio are output from Front L and Front R.
“Network”
IP Address/DNS Settings (> 12)
≥Press [OK] to show the following settings.
Connection Test — — — —
IP Address Auto Configuration (DHCP) ≥On
≥Off
IP Address — — —. — — —. — — —. — — —
Subnet Mask — — —. — — —. — — —. — — —
Default Gateway — — —. — — —. — — —. — — —
DNS Auto Configuration (DHCP) ≥On
≥Off
Primary DNS — — —. — — —. — — —. — — —
Secondary DNS — — —. — — —. — — —. — — —
Auto Detect Connection Speed ≥On
≥Off
Connection Speed Setting
This is enabled only when “Auto Detect Connection Speed” is
turned “Off”.
≥10BASE Half Duplex
≥10BASE Full Duplex
≥100BASE Half Duplex ≥100BASE Full Duplex
Proxy Server Settings (> 13)
≥Press [OK] to show the following settings.
Reset to factory preset
Proxy Address (The initial setting is blank.)
Proxy Port Number (The initial setting is “0”.)
DMP-BD50PP-RQT9184_eng.book 28 ページ ２００８年４月４日 金曜日 午後８時１４分