Filter
Top Products
34
RQT9184
(ENG)
Messages
The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and
use.
On the television Page
Authorization Error
This unit is not authorized to
play this title.
≥You are trying to play the DivX VOD content that was purchased with a different
registration code. You cannot play the content on this unit.
20
Cannot play. ≥You inserted an incompatible disc (Discs recorded in PAL video, etc.).
4, 5
Cannot display on this unit. ≥You tried to play a non-compatible image.
≥Confirm “SD” on the unit’s display is not blinking and re-insert the card.
5, 22
—
No disc is inserted. ≥The disc may be upside down. —
Rental Expired. ≥The DivX VOD content has zero remaining plays. You cannot play it. 20
$ This operation is currently
disabled.
≥The operation is prohibited by the unit or disc.
—
Cannot connect.
Please check the connection of
the LAN cable.
≥When a hub is used but its Link lamp does not light up, check the cable connection, LAN
terminal connection, cable itself (a cross cable may be used by mistake), etc.
9
IP address is not set. ≥The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---“. Set the “IP Address”,
“Subnet Mask”, and “Default Gateway“. (Select the automatic address acquisition if
necessary.)
12
Cannot obtain IP address using
DHCP.
Please check the connection or
router settings.
≥If you use a hub, then check the connection between the hub and the router.
–Use the UPLINK port of the hub to connect to a router.
–Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the
cable connection, LAN terminal connection, cable itself (a cross cable may be used by
mistake), etc.
≥If the above conditions are OK, then the router may not operate in DHCP mode. Check the
router settings and operation. You may reset the router to restore it to normal.
9
This IP address is already in
use.
Please check the IP address
setting.
≥This unit’s IP address is used by another device. Check the IP addresses of this unit,
personal computers, and routers, etc. If necessary, reconfigure them to avoid IP addresses
from being duplicated.
—
Unable to perform Connection
Test.
Please try again.
≥Turn the unit off. Remove the power cord and reconnect it and try again. If the same
symptom persists, then consult your dealer.
—
IP address not set correctly.
Connection Test was
unsuccessful. No reply
from host.
Please check the connection or
router settings.
≥If you use a hub, then check the connection between the hub and the router.
–Use the UPLINK port of the hub to connect to a router.
–If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal
connection, cable itself (a cross cable may be used by mistake), etc.
≥Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP Address/DNS
Settings”.
≥If the MAC address information is required, then press [SETUP] to display the “Network”
menu.
9
12
12
Network connection refused.
Please confirm Setup “BD-Live
Internet Access”
≥When you set “BD-Live Internet Access” to “Allow (Limited)” and play BD-Live contents
which do not have a content owner certificate, the Internet access of the content is not
allowed. If you allow the content to connect to Internet, set “BD-Live Internet Access” to
“Allow (ALL)”.
26
On the unit’s display
F99 ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to
standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.
—
HDMI ONLY ≥Some BD-Video discs can only be output with HDMI. —
No PLAY ≥There is a viewing restriction on a BD-Video or DVD-Video. 26
No READ ≥The disc is dirty or badly scratched. The unit cannot play. —
PLEASE WAIT ≥Displayed when the unit is started and turned off. This is not a malfunction.
≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE
WAIT” is displayed.
—
—
SET
(“ ” stands for a number.)
≥The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
33
UNFORMAT ≥You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format).
—
UNSUPPORT ≥You have inserted a disc the unit cannot play. 4, 5
U59 ≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
—
U72
U73
≥The HDMI connection acts unusually.
–The connected equipment is not HDMI compatible.
–Please use HDMI cables that have the HDMI logo (as shown on the cover).
–The HDMI cable is damaged.
—
DMP-BD50PP-RQT9184_eng.book 34 ページ ２００８年４月４日 金曜日 午後８時１４分