Filter
Top Products
17
RQT7450
Recording
Timer recording
[RAM] [DVD-R]
You can enter up to 16 programmes up to a month in advance.
Entering G-
CODE numbers is an easy way of timer recording. You can
find these numbers in TV listings in newspapers and magazines.
1 Press [G-Code].
2 Press the numbered buttons to enter
the G-CODE number.
Press [2] to move back to correct a digit.
3 Press [ENTER].
≥Confirm the programme and make corrections if necessary
using [3, 4, 2, 1] (➡page 18, step 3).
≥When “-- ---” appears in the “Name” column, you cannot set
timer recording. Press [3, 4] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit’s memory.
≥You can also press [REC MODE] to change the recording
mode.
≥Programme Name
Press [2, 1] to select “Programme Name” and press
[ENTER] (➡page 38).
4 Press [ENTER].
The settings are stored.
Repeat steps 1–4 to programme other recordings.
5 Press [F TIMER].
The unit turns off and “F” lights on the unit’s display to
indicate timer recording standby has been activated.
[RAM]
Even if the unit is in timer recording standby, play starts when you
press [1] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.
Using G-CODE
®
system to make timer
recordings
VOLUME
CH
DVD
TV
AV
123
456
78
0
9
MANUAL SKIP
CH
CANCEL
SKIP
STOP
PAU SE
PLAY/x1.3
SLOW/SEARCH
FUNCTIONS
ENTER
DIRECT NAVIGATOR
TOP MENU
RETURN
SUB MENU
CREATE
CHAPTER
TIMER
PROG/CHECK
REC MODEERASE
REC
AUDIO
TIME SLIP
STATUS
DISPLAY
F
A B C
DVD
SD/PC
DRIVE SELECT
DIRECT
NAVIGATOR
INPUT SELECT
G-Code
-/--
3,4,2,1
ENTER
F TIMER
PROG/CHECK
REC MODE
PLAY
¢ CANCEL
G-Code
Numbered
buttons
1:58 SP
G-Code
Remain
12:53:00 15. 7. TUE
Enter G-Code Number by using 0-9 keys.
Mode
StopStart
Name
Date
1:58 SP
TIMER
RECORDING
Remain
12:54:00 15. 7. TUE
Programme Name
20:0019:0015/ 7 TUE SP 1 ARD
∫ To release the unit from recording standby
Press [F TIMER].
The unit turns on and “F” goes out.
≥Be sure to press [F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if “F” is displayed.
∫ To cancel recording when recording has
already begun
Press [F TIMER].
≥You can also press and hold [∫] on the main unit for more than
3 seconds to stop recording.
[Note]
≥“F” flashes for about 5 seconds when the unit cannot go to
timer recording standby (e.g., a recordable disc is not in the
disc tray).
≥If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the “F” flashes on the unit display. In this case,
press [F TIMER] to put the unit in the timer recording standby
mode.
≥When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R).
SP
OK
20:0019:00ARD 15/ 7 TUE01
Mode
Disc
space
StopStartNo.
Name
Date
1:58 SP
TIMER
RECORDING
Remain
12:55:00 15. 7. TUE
New Timer Programme
Check to make sure
“OK” is displayed
(➡page 19).
7450L.book 17 ページ ２００４年５月１２日 水曜日 午後３時２３分