Filter
Top Products
48
RQT7450
Reference
Error messages
On the television Page
On the unit’s display
Cannot finish recording
completely.
≥The programme was copy-protected.
≥The disc may be full.
—
—
Cannot playback this title.
TV system is different from the
setting.
To playback this title, please
change the TV System in
SETUP.
≥You tried to play a title recorded using a different encoding system from that of the TV
system currently selected on the unit.
Alter the “TV System” setting on this unit to suit.
43
Cannot record on the disc. ≥The disc may be dirty or scratched.
≥You cannot format a Microdrive or mobile hard disk on this unit.
44
—
Please check the disc.
Unable to format.
Cannot play on this unit. ≥You tried to play a non-compatible image.
≥Turn the unit off and re-insert the card.
24
24
Cannot record. Disc is full. ≥Create space by erasing any unnecessary titles. [RAM]
(Even if you erase recorded content from the DVD-R, there is no increase in disc space.)
≥Use a new disc.
22, 29,
36, 37
—
Cannot record. Maximum
number of titles exceeded
Error has occurred. Please
press ENTER.
≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering
(“SELF CHECK” appears on the unit’s display).
—
No Disc ≥The disc may be upside down. —
No folders. ≥There is no compatible folder in this unit. 13
No PC CARD
No SD CARD
No valid PC card.
No valid SD card.
≥The card is not inserted. If this message is displayed with a compatible card already
inserted, turn off the unit, remove and then re-insert the card.
≥The card inserted is not compatible or the card format does not match.
24
13
Not enough space on dubbing
destination.
≥Create space by erasing any unnecessary items. 22, 25, 29,
32, 36, 37
Please change the disc. ≥There may be a problem with the disc. Press [< OPEN/CLOSE] on the main unit to
remove it and check it for scratches or dirt. (The unit turns off automatically after you open
the tray.)
44
This is a non-recordable disc. ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.
≥You inserted an unformatted DVD-RAM. Format the disc with this unit.
—
37
This disc is not properly
formatted.
Formatting is necessary using
DISC MANAGEMENT.
$
≥The operation is prohibited by the unit or disc. —
HARD ERR ≥If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
—
NO READ ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥You have used a DVD-RAM/PD lens cleaner and it has finished. Press [< OPEN/CLOSE]
on the main unit to eject the disc.
44
—
PROG FULL ≥There are already 16 timer programmes. Delete unnecessary timer programmes. 19
REMOTE DVD
(“∑” stands for a number.)
≥The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [ENTER] and the indicated number
button at the same time for more than 2 seconds.
11
SELF CHECK ≥The unit is starting up. Wait until the message disappears. —
U14 ≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
—
U99 ≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standby.
Now press [Í/I] on the main unit again to turn the unit on.
—
UNSUPPORT ≥You have inserted a disc the unit cannot play or record on. 12
X HOLD ≥The Child Lock function is activated.
Press and hold [ENTER] and [RETURN] simultaneously until “X HOLD” disappears.
44
7450L.book 48 ページ ２００４年５月１２日 水曜日 午後３時２３分