Filter
Top Products
16
RQT7392
Recording
Recording television programs
[HDD] [RAM] [DVD-R]
≥It is not possible to record to both HDD (Hard Disk Drive) and DVD
drive simultaneously.
≥You can record up to 500 titles on HDD, 99 titles on one disc.
≥It is not possible to record continuously from one side of a double
sided disc to the other. You will need to eject the disc and turn it
over.
≥W
hen using 8 cm (3
″
) DVD-RAM, remove the disc from the cartridge.
≥It is not possible to record CPRM (➡ page 53) protected material
onto DVD-R or 2.8 GB DVD-RAM discs.
≥It is not possible to record to a card.
Preparation
Press [RETURN] to exit the television program list if it is displayed on
the television. To turn off auto start up of the television program list
➡ page 23, Selecting the TV Guide On Screen
TM
system start up
pattern.
1 Press [HDD] or [DVD] to select the
recording drive.
The HDD or DVD indicator lights up on the unit.
2 If you selected the DVD drive
Press [< OPEN/CLOSE] on the main
unit to open the tray and insert a disc.
≥Press the button again to close the tray.
3 Press [WXCH] to select the channel.
To select with the numbered buttons:
≥Select the audio to record (➡ page 17).
4 Press [REC MODE] to select the
recording mode (XP, SP, LP, or EP).
≥To record sound using LPCM (XP mode only):
Set “Audio for XP Recording” to “LPCM” in the SETUP menu
(➡ page 49).
5 Press [¥ REC] to start recording.
Recording will take place on open space on the HDD or on
disc. Data will not be overwritten.
≥You cannot change the channel or recording mode during
recording.
≥You can record while the unit is on standby for timer recording, but
once the time for the timer recording to begin is reached, any
recording taking place will stop and the timer recording will begin.
∫ To stop recording
Press [∫].
From the start to the end of the recording is called one title.
[HDD]
When continuously recording for long durations, titles are
automatically divided every 8 hours.
[DVD-R]
It takes about 30 seconds for the unit to complete recording
management information after recording finishes.
∫ To pause recording
Press [;].
Press again to restart recording.
(Title is not split into separate titles.)
When transferring (dubbing) in high speed mode to DVD-R
after you have recorded to the HDD.
Set “DVD-R High-Speed Recording” to “On” before recording to
the HDD (➡ page 48).
However, the following restrictions apply.
≥Even 16:9 aspect (Widescreen) programs are recorded in 4:3
aspect.
≥Even if “Hybrid VBR Resolution” is set to “Automatic”, it
changes to “Fixed” automatically (➡ page 48).
When recording to DVD-R
≥When recording MTS broadcasts, only the audio selected in
“Select MTS” (➡ page 48) is recorded (“Main” or “SAP”).
≥In order to play a DVD-R recorded using this unit on
another playback source, the disc must first be finalized
(➡ page 45).
POWER
VOLUME
CH
INPUT SELECT
DVD POWER
TV
TV/VIDEO
1
HDD
SD/PC
DVD
23
456
78
0
9
CM SKIP
AUDIO
PAG E
CH
CANCEL
VCR Plus+
SKIP
STOP
PAU SE
PLAY/x1.3
SLOW/SEARCH
FUNCTIONS
ENTER
DIRECT NAVIGATOR
TOP MENU
RETURN
SUB MENU
CHAPTER
SETUP
Info
PROG/CHECK
TV GUIDE
REC MODEERASE
REC
STATUS
TIME SLIP
DISPLAY
DUBBING
REC
TIME SLIP
SD PC
DVDHDD
OPEN/CLOSE
DRIVE SELECT
POWER
CHTIME SLIP
SD CARD PC CARD EJECT
/
x
1.3
AUDIO
1
3 4 2 1
ENTER
RETURN
TIME SLIP
3
4
5
FUNCTIONS
STATUS
DIRECT
NAVIGATOR
1
∫
;
3
2
∫
1
1
5
TIME SLIP
Numbered
buttons
Time Slip indicator
HDD, DVD indicator
TV Mode (Airwaves)
e.g., 5: [0] ➡ [5]
15: [1] ➡ [5]
CATV Mode (Cable)
e.g., 5: [0] ➡ [0] ➡ [5]
15: [0] ➡ [1] ➡ [5]
115: [1] ➡ [1] ➡ [5]
Insert with the arrow facing in.
Insert fully so it
clicks into place.
Insert label-up.
HDD
SP
CH
HDD
XP
CH
Remaining time on the disc
HDD
XP
CH
REC
7392en.book 16 ページ ２００４年４月２７日 火曜日 午後５時３０分