Filter
Top Products
47
RQT9464
Displays Page
TV screen and video
The display is dim. ≥Change “FL Display” in the Setup menu.
36
The elapsed time displayed
is actually less than the
play time.
≥The displayed play time is converted from the number of frames at 29.97 frames
(equal to 0.999 seconds) to one second. There will be a slight difference between
the time displayed and the actual elapsed time (e.g., actual one-hour elapsed time
may display as approximately 59 minutes 56 seconds).
—
The images from this unit
do not appear on the
television.
Picture is distorted.
Jittering occurs.
≥Make sure that the television is connected to the VIDEO OUT terminal or the
HDMI AV OUT terminal on this unit.
≥Make sure that the television’s input setting (e.g., AV 1) is correct.
≥An incorrect resolution is selected in “HDMI Video Format”, when the television is
connected to HDMI AV OUT terminals. While stopped, press and hold [1] and [∫]
on the main unit at the same time for more than 5 seconds to cancel this setting.
Set the item again. However, Dolby Digital Plus, Dolby TrueHD, and DTS-HD
audio are not output in bitstream. To output the bitstream, select “Default Settings”
to restore the factory presets and make proper settings.
≥If “24p Output” is set to “On” when the unit is connected to a TV through any
terminal other than HDMI, images may not display properly. In this case, set “24p
Output” to “Off”.
≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p
images switch to other images, and a black screen is displayed.
≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video. In
this case, turn “24p Output” to “Off”.
≥Picture may not be seen when more than 2 devices are connected with HDMI
cables.
Reduce the number of connected devices.
≥The unit and television are using different video systems. While stopped, keep
pressing [∫] and [DISC < OPEN/CLOSE] on the main unit for 5 or more seconds.
The system switches from PAL to NTSC or vice versa.
≥The system used on the disc doesn’t match your television.
–PAL discs cannot be correctly viewed on an NTSC television.
–This unit can convert NTSC signals to PAL60 for viewing on a PAL television
(“NTSC Contents Output” in the “Picture”).
≥
[DivX] Images may not be output due to how files were created.
≥If you are using an indoor TV antenna, change to an outdoor antenna.
≥The TV antenna wire is too close to the unit. Move it away from the unit.
9
—
37
37
37
37
—
—
—
35
—
—
—
Picture stops. ≥[DivX] Picture may stop if the DivX files are greater than 2 GB.
—
The screen changes
automatically.
≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display
may return to the screen saver mode automatically if there is no operation for
5 minutes or more.
36
Video is not output. ≥An image is not output from the VIDEO OUT terminal when the “High Clarity
Sound” is enabled. Set the “High Clarity Sound” in the on-screen menu to “Off” to
use the VIDEO OUT terminal.
34
Video is not output in high
definition.
≥High definition video cannot be output through the VIDEO OUT terminal.
≥Confirm that the “HDMI Video Format” in the Setup menu is set properly.
—
37
The Setup menu cannot be
accessed.
≥Select “BD/DVD” as the source.
14
Status messages do not
appear.
≥Select “Automatic” in “On-Screen Messages” in the Setup menu.
36
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
≥Use the television to change the aspect. Refer to your television’s operating
instructions.
≥When using an HDMI cable, set “TV Aspect” to “16:9”.
—
37
When playing DVD-Video
using progressive output,
one part of the picture
momentarily appears to be
doubled up.
≥Connect this unit to the TV with any cable except the HDMI cable.
9
There is no apparent
change in picture quality
when adjusted with the
“Picture” menu in the
on-screen menu.
≥The effect is less perceivable with some types of video.
—
The masked-off area is
masked in grey.
≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off
area is displayed in black.
36
Still pictures (JPEG) do not
playback normally.
≥The images that were edited on the PC, such as Progressive JPEG, etc., may not
playback.
44
After choosing “Home
Cinema” in “Speaker
selection” with the TV’s
remote control, the TV’s
input selection also
changes.
≥Disconnect the HDMI cable from the TV and reconnect it to a different HDMI
terminal.
—
Reference
SC-BTX70EGEB-RQT9464-B.book 47 ページ ２００９年４月９日 木曜日 午後２時５３分