Filter
Top Products
Diagnostic Software, Trouble Shooting and Test Instructions
EN 38 DVD763SA5.
5.8.3 Display PWB Nuclei
5.8.4 Processor & Peripherals Nuclei
5820 Test successful
5840 Test successful
5860 Test successful
5801 "Unexpected response from Basic Engine"
7000 "Manuf. ID: <XX>" "Device ID: <YY>"
7001 "Comm Test Failed"
7002 "Load Cmd Failed"
7003 "Load Dat Failed"
7004 "Run Cmd Failed"
7100 "ROM Checksum: XXXX"
7101 "Comm Test Failed"
7102 "Load Cmd Failed"
7103 "Load Dat Failed"
7104 "Run Cmd Failed"
7201 "Comm Test Failed"
7200 "Test successful"
7202 "Load Cmd Failed"
7203 "Load Dat Failed"
7204 "Run Cmd Failed"
7205 "Scratch circuit not OK"
Error
code Error text
3000 “Test successful”
3001 “Disp not responding”
3002 “Disp key no response”
3003 “One or more patterns not correct”
3004 “Disp type invalid”
3020 “Test successful”
3021 “Disp not responding”
3022 “Disp key no response”
3023 “One or more patterns not correct”
3040 “Test successful”
3041 “Disp not responding”
3042 “Disp key no response”
3043 “One or more patterns not correct”
2700 “Model name in wich the test is running”
2701 “Disp key no response”
2702 “Disp not responding”
2707 “Stop key not pressed”
2708 “Pause key not pressed”
2709 “Play key not pressed”
2710 “Open/close key not pressed”
2713 “Previous key not pressed”
2714 “Next key not pressed”
2715 “More than one key not pressed”
2716 " Audio key not pressed"
2900 “Test successful”
2901 “Slave not responding”
2902 “Slave keyboard not responding”
2903 “Standby led not working”
2800 “Test successful”
2801 “Slave display controller not responding”
2802 “Slave keyboard not responding”
2803 “No key press received from remote control”
Error
code Error text
2600 “The ROM version of the slave processor =
0xXX, and the internal ID = 0xYY”
2601 “I2c bus busy”
2602 “I2c bus not working“
6000 P50 test
6001 “No readback on P50”
6002 “Disp not responding “
6003 “P50 readback error”
Error
code Error text
700 Test successful
720 Test successful
740 Test successful
600 "All checksums are correct"
601 “Following checksum is faulty: BootCode1
Checksum is 0xY2 and is not correct (must be
0xZ2)”
601 “This test is not available when stand-alone
compiled”
6200 "Checksums = 0xA1, 0xB1, 0xC1, 0xD1"
6201 “This test is not available when stand-alone
compiled”
1000 Test successful
1001 Test successful
1020 Test successful
1021 Test successful
1100 Test successful
1104 “NVRAM reply time-out”
1200 Test successful
1202 “Slave bus not working”
1203 “Slave controller not responding”
1204 “Slave response is not correct”
5900 Test successful
5901 “I2c bus busy”
5902 “I2c bus not working“
5904 “DTS chip response not correct”
1300 Test successful
1301 “Parity error from basic engine to serial”
1302 “Parity error from serial to basic engine”
1303 “No communication between serial and basic
engine”
1304 “Communication time-out error”
1600 Test successful
1601 “The DVD SDRAM is faulty”
Error
code Error text