Pioneer DVR-420H DVD Recorder User Manual


 
The Initial Setup menu
13
98
En
Set the date (day/month/year) and time, then
press ENTER to make all the settings.
Use the
/
(cursor up/down) buttons to change
the value in the highlighted field.
Use the
/
(cursor left/right) buttons to move
from one field to another.
Input Line System
Default setting:
625System
For standard PAL or SECAM recording, leave the input
line system to
625System
. When recording an NTSC or
PAL–60 signal through an external input, change to
525System
.
Note
When the current input is a built-in tuner channel
preset, changing the input line system will usually
also affect the input line system of the
AV2/AUTO
START REC (INPUT 1/DECODER)
input. However if
the
AV2/L1 In
setting is set to
Decoder
(see
AV2/L1
In
on page 102), then the L2 input is affected instead.
If when this setting is changed, the screen goes
blank (due to incompatibility with your TV), you can
switch back by pressing and holding the front panel
+
button then pressing
DVD
(also front panel) while
the recorder is stopped.
When you switch the Line Input System setting the
Copy List is erased. If you switch the setting using the
+
button and
DVD
buttons as described above, there
is no confirmation, so please use with care.
You can’t mix recordings of different TV line systems
on the same disc.
When you change this setting, the
Input Colour
System
setting also changes (see
Input Colour
System
on page 102).
On Screen Display
Default setting:
On
On the default setting, the recorder shows on-screen
operation displays (
Play, Stop
and so on). Change to
Off
to hide these displays.
Front Panel Display
Default setting:
On
On the default setting, the time is shown in the front
panel display when the recorder is in standby. Switch to
Off
to have the front panel display switch off completely
when in standby.
Note
When set to
Off
, the display still lights dimly in
standby when setting a timer recording, or during
Auto Start Recording.
Power Save
Default setting:
Off
When set to
Off
, signals arriving at the
ANTENNA IN
terminal and at the
AV2/AUTO START REC (INPUT 1/
DECODER)
AV connector are passed through to the
ANTENNA OUT
terminal and to the
AV1(RGB)-TV
AV
connector, respectively, when the recorder is in standby.
You can cut the standby power consumption of the
recorder by turning off the through function for one or
both terminals:
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
Clock Setting
Manual Clock Setting
2/2
Date
Time
Time Zone
Summer Time
01 01 2004
THU
00 00
England
London
On
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
525System
625System
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
On
Off
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
On
Off
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
Mode1
Mode2
Off
Initial Setup
DVR-04_HDD_UK.book 98 ページ 2004年4月11日 日曜日 午後6時11分