Filter
Top Products
The Initial Setup menu
12
84
En
Bilingual Recording
• Default setting:
A/L
When recording a bilingual source from an external input
in Video mode or VR mode set to
FINE/MN32
, you can
choose to record either the
A/L
(left), or the
B/R
(right)
audio channel.
Note
• If you’re recording in VR mode (except when set to
FINE/MN32
), both channels will be recorded and you
can switch them as you like on playback.
DV Input (DVR-320 only)
• Default setting:
Stereo1
You need to set this if you have a camcorder using 32kHz/
12-bit sound connected to the front panel
DV IN/OUT
jack.
Some digital camcorders have two stereo tracks for
audio. One is recorded at the time of shooting; the other
is for overdubbing after shooting.
On the
Stereo1
setting, the sound that was recorded
while shooting is used. On the
Stereo2
setting, the
overdubbed sound is used. You can also choose a
Mix
setting of 25%, 50% or 75% for the Stereo 1 with a
corresponding Stereo 2 setting of 75%, 50% or 25%.
Input Level (L1 / L2)
• Default setting:
0dB
You can adjust the gain of the audio from each external
input individually, from
–6dB
to
+6dB
in steps of 3 dB to
optimize the recorded audio level.
Audio Out settings
Digital Out
• Default setting:
On
If at any time you need to switch off the digital audio
output, set this to
Off
, otherwise leave it
On
.
Note
• When set to
Off
, all the other
Audio Out
settings are
grayed out and can’t be set.
Dolby Digital Out
You only need to make this setting if you connected this
recorder to an AV amp/receiver (or other component) using
the digital output.
• Default setting:
Dolby Digital
If your AV amp/receiver (or other connected component)
is Dolby Digital compatible, set to
Dolby Digital
,
otherwise set to
Dolby Digital
PCM
. Check the
manual that came with the connected component if
you’re unsure whether it is Dolby Digital compatible.
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
NICAM Select
Tuner Level
External Audio
Bilingual Recording
DV Input
Input Level (L1)
Input Level (L2)
A/L
B/R
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
NICAM Select
Tuner Level
External Audio
Bilingual Recording
DV Input
Input Level (L1)
Input Level (L2)
Stereo1
Stereo2
Mix (Stereo1: 75%)
Mix (Stereo1: 50%)
Mix (Stereo1: 25%)
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
NICAM Select
Tuner Level
External Audio
Bilingual Recording
DV Input
Input Level (L1)
Input Level (L2)
Initial Setup
+6dB
+3dB
0dB
–3dB
–6dB
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Digital Out
Dolby Digital Out
DTS Out
96kHz PCM Out
MPEG Out
On
Off
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Digital Out
Dolby Digital Out
DTS Out
96kHz PCM Out
MPEG Out
Dolby Digital
Dolby Digital PCM
Initial Setup
DVR-04_UK.book 84 ページ ２００４年４月１１日 日曜日 午後５時２０分