Filter
Top Products
GB
29
GB
28
Protecting a Recorded Cassette
Recording a Programme Immediately
Video cassettes have a safety tab to prevent accidental erasure.
When this tab has been removed, you cannot
record on the tape.
1 If you wish to protect a cassette, break off the tab using a small
screwdriver.
2 To re-record over a protected cassette (safety tab broken), cover
the hole with adhesive tape.
Before recording a programme, you must have preset the corres-
ponding station (unless you are recording via an external video
source). If you have not done so, refer to pages 19 and 20.
1 Switch on the television.
2 To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3 Insert the cassette on which the programme is to be recorded, with
the window visible and the safety tab intact or the opening covered
with adhesive tape.
Result
: The DVD-VCR is switched on automatically.
4 Select:
◆
The station to be recorded using
the PROG/TRK (
"
or
❷
)
buttons
or
◆ The LINE source using the INPUT SEL. button for a satellite
tuner or external video source
Result: The station number is displayed and the programme
can be seen on the television.
5 Select the recording speed by pressing the SPEED button as
many times as required (see page 28).
6 Hold REC (
●
) down for a while to start recording.
Result
:
The record indicator appears on the television and DVD-
VCR display. An index is recorded on the tape (see page
38).
7 To stop recording, press
■
once.
➢ ◆ If your DVD-VCR ejects the cassette when you start
recording, check to make sure that the cassette’s
safety tab is intact or that the opening (created by a
broken safety tab) is covered with adhesive tape.
◆ If you reach the end of the tape while recording, the
cassette rewinds automatically.
1
7
0
ANGLE AUDIO
6
4
4
5
Displaying/Hiding On-Screen Information
Selecting the Recording Speed
Your DVD-VCR displays most information both on the DVD-VCR
and the television.
You can choose to display or hide this information on the television
screen (except for the Index, MAIN MENU and Timer functions,
which cannot be hidden).
1 Press SETUP on the remote control.
Result
: The MAIN MENU is displayed.
2 Press the corresponding
"
,
❷
buttons to select the VCR Setup
option.
3 Press the ENTER button to select this option.
4 Press the corresponding
"
,
❷
buttons to select the OSD menu.
5 To... Press
➛
or
❿
, until...
Display on-screen information ONis displayed.
Hide on-screen information OFFis displayed.
6 On completion, press RETURN to exit the menu.
You can record a cassette at two different speeds:
◆ SP (Standard Play)
◆ LP (Long Play)
In Long Play modes:
◆ Each cassette lasts twice as long
◆ The recording is of a slightly lower quality
To record a cassette... Press the SPEED button on the
remote control, until...
In standard play mode SP is displayed.
In long play mode
LP is displayed.
Type Recording Time (in SP)
E-180 180 mins. or 3 hours
E-240 240 mins. or 4 hours
E-260 260 mins. or
4 hours and 20 mins.
E-300 300 mins. or 5 hours
DVD
Clock Set
Installation
Tape Select
E180
Repeat play
OFF
OSD
ON
Return
Enter
DVD
DVD
DVD
Language
DVD Setup
VCR Setup
Option
Program
Parental
DVD
DVD
VCR
VCR
VCR
VCR
00115A DVD-V77MS-GB2 10/25/02 10:46 AM Page 28