Samsung DVD-V77MS DVD VCR Combo User Manual


 
Using the TV Buttons on the Remote Control
43
GB
42
GB
Audio Dubbing a Pre-recorded Cassette
With the Audio Dubbing function, you erase the previously
recorded sound and replace it with a new soundtrack from:
A CD, DVD
A microphone connected to a sound system
A cassette player
Restriction:
Audio dubbing is applicable only to the longitudinal audio track
(normal audio).
1 Connect an RCA audio cable to the appropriate output on your
sound system (cassette player for example).
2 Connect the other end of the RCA audio cable to the audio input
connectors (L, R) on the Front of your DVD-VCR.
3 Insert the pre-recorded cassette on which the audio track is to be
replaced, and press the
ll
to start playback.
4 Search for the Audio Dubbing (ending) point using the
❿❿
, and set
the counter to 0:00:00 by pressing CLOCK/COUNTER and
CLEAR.
5 Search back slightly beyond the Audio Dub start point using the
➛➛
button.
6 Press the
ll
button.
Press the
ll
button one more time to make STILL mode.
7 Press A.DUB.
Result
: Your DVD-VCR is now in the Audio dubbing Still
mode.
8 Press the INPUT SEL. button to select Audio dubbing source.
ex) If you want to dub external cassette player, then select LINE.
9 On the sound system, locate the point on the cassette at which
you wish to start playback.
Example
: The track that you wish to record on the cassette.
10 When you are ready:
Start playback on the sound system
Press the REC on the remote control.
Result
:
The soundtrack is replaced on the pre-recorded cassette.
11 The audio dubbing will finish when the counter reaches 0:00:00.
The new sound will be recorded on the normal sound track
of the tape, and the original sound will remain on the Hi-Fi
sound track. To hear the new sound and original sound
mixed together, press the Audio button on the remote
control until the MIX option is displayed (see page 36).
Select LINE by pressing the INPUT SEL button until you hear
the sound you want to dub.
4 5
6
10
A.DUB
A.DUB
VIDEO EDIT
A.DUB
-0:05:23
7
EC VIDEO
L
AUDIO
R
LINE IN 2
2
2
VCR VCR
Your DVD-VCR remote control will work with Samsung televisions
and compatible brands.
To determine whether your television is compatible, follow the instructions
below.
1 Switch your television on.
2 Point the remote control towards the television.
3 Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
Brand Codes Brand Codes
SAMSUNG 01 to 06 PHILIPS 02, 20, 22
AKAI 09, 23 SABA 13, 14, 22 to 24
GRUNDIG 09, 17, 21 SONY 15, 16
LOEWE 02 THOMSON 13, 14, 24
PANASONIC 08, 23 to 27 TOSHIBA 07, 16 to 19, 21
Result:
If your television is compatible with the remote control, it
will switch off. It is now programmed to operate with the
remote control.
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
When you change the batteries in the remote control, you
must reprogramme the code, following the same procedure.
You can then control the television using the following buttons.
Button Function
STANDBY/ON
Used to switch the television and DVD-VCR on and off.
TV or VCR
Used to switch between the TV and VCR modes.
INPUT SEL.
Used to select an external source.
VOL + or
Used to adjust the volume of the television.
PROG/TRK
Used to select the required programme.
(
$
or
)
TV MUTE
Used to mute the volume of the television.
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
231
564
8
0
97
ANGLE AUDIO
231
564
0
ANGLE AUDIO
0
ANGLE AUDIO
1
2
2
5
5
4
4
3
6
00115A DVD-V77MS-GB3 10/25/02 10:48 AM Page 42