1 – Introduction
TASCAM CC-222MKIV 17
4 – Disc operations
Playback modes
The unit can be set to play back a single track, the whole
disc in the created order, the tracks of the disc in a random
(shuffled) order, or a programmed order. This operation
takes place when stopped.
NOTE
Selecting the playback mode is only possible using the
remote control unit.
1 Whenstopped,pressthePLAY MODEkeyonthe
remotecontrolrepeatedlytocyclethedisplay
throughthefollowing:
•
Continue. Normal playback mode. Playback contin-
ues in the normal order.
•
Single. The currently selected track is played and
then playback stops. The
SINGLE indicator lights in this
mode.
•
Random. In this mode, all the tracks on the disc are
played in random order, and the
RANDOM indicator lights
(see “Random playback” on page 17 below).
•
Program. The PROGRAM indicator lights in this mode
(see “Program playback” on page 17 below).
The selected mode is shown in large characters dis-appears
from the display a few seconds after selecting the mode,
and the display returns to its previous mode.
Program playback
The steps to set up to 99 program steps (tracks) to be
played back in a specified order are as follows:
1 Whenstopped,pressthePLAY MODEkeyuntilthe
displayshowsProgram.
2 Thedisplaychangestoshow0Tr 00:00 00,
meaningthattherearenotracksassignedforpro-
gramplayback.
3 Usethenumberkeysontheremotecontroltoenter
atracknumber.ThereisnoneedtopresstheEN-
TER
key.
Thetrackenteredisassignedtotheprogramstep,
andthedisplaychanges,showingthetracknumber,
thetotaltimeoftheprogramsofar,andthestep
number,e.g.2Tr 14:56 03.
4 Thenextprogramstepcanthenbeentered.
NOTE
Steps 3 and 4 above can also be carried out from the
main unit by turning and pushing the MULTI DIAL key.
5 Repeatsteps3and4aboveuntiltheprogramis
complete.
6 PressthePLAYkeytostartplaybackattherst
programstep.
Thedisplayshowsthetrack,thecurrenttimedis-
play,andtheprogramstepnumber.
Whileinprogramplaybackmode,usingtheSKIP
keysortheMULTI DIALmovesbackwardsandfor-
wardsintheordersetintheprogram.
Use the PAUSE key to stop playback temporarily or the
STOP key to stop playback of the program. If the STOP
key is used, when playback is restarted, it starts from the
first program step.
When stopped, if the
CLEAR key on the remote control is
pressed, it cancels the last track entered in the program.
Clear the program by pressing the
PLAY MODE until the
display shows
Continue. The program is also cleared
when the disc tray is opened, and if the
STOP key is
pressed when playback is stopped in programmed order
mode.
The programmed play order is not memorized when the
power is turned off.
If you enter more than 99 program steps, the message
PGM
Full !
appears on the display.
If the total time programmed goes over 100 minutes, the
message
--:-- appears on the display.
In this mode, the unit will playback all the tracks on the
disc in random order.
1 Whenstopped,pressthePLAY MODEkeyuntilthe
displayshowsRandom.
2 PressthePLAYkeytostartrandomplayback.
Whileplayingback,usingthetrackskipfunction
willmoveforwardsthroughtherandomorder.Turn
the MULTI DIALontheunitclockwiseorpressthe
SKIP(¯)keyontheremotecontrol.
NOTE
You cannot go backwards to previous tracks in the
Random playback mode.
To stop random playback, press the STOP key. Opening
the disc tray also stops random playback.
Random playback