Filter
Top Products
11EN
Disc
Management
Recording Playback
Introduction
Connections Basic Setup Editing Function Setup VCR Function Others
FUNCTIONAL OVERVIEW
Front Panel
18 15 14 131920 1617 12 11 8*97
1 2 43* 5
10
6
Rear Panel
1 2
591113 10 8 6712
3
4
(
*
) The unit can also be
turned on by pressing
these buttons or by
inserting a cassette tape.
1. I/
y
ON/STANDBY button
• Press to turn on the unit, or to turn the unit into the
standby mode. (To completely shut down the unit, you
must unplug the AC power cord.)
2. Cassette compartment (VCR)
• Insert a cassette tape here.
3. A OPEN/CLOSE button (DVD)*
• Press to open or close the disc tray.
4. Disc tray (DVD)
• Place a disc when it is open.
5. VIDEO input jack (L2)
• Use to connect external device with an RCA video cable.
6. AUDIO input jacks (L2)
• Use to connect external device with an RCA audio cable.
7. I REC button (DVD)
• Press once to start a recording.
• Press repeatedly to start the one-touch timer recording.
8. PLAY B button (DVD)*
• Press to start or resume playback.
9. STOP C button (DVD)
• Press to stop playback or recording.
• Press to stop the proceeding timer recording in DVD.
10. VCR/DVD button
• Press to select the component you wish to operate.
11. VCR/DVD indicator
• Lights up when the VCR/DVD output mode is selected.
12. DUBBING button
• Press to start VCR to DVD (DVD to VCR) duplication which
you set in the main menu.
13. CHANNEL / buttons
• Press to change the channel up and down.
14. Display (“Off” in standby)
• Refer to “FRONT PANEL DISPLAY GUIDE” on page 18.
15. Infrared sensor window
• Receive signals from your remote control so that you can
control the unit from a distance.
16. I REC button (VCR)
• Press once to start a recording. Press repeatedly to start the
one-touch timer recording.
17. PLAY B button (VCR)
• Press to start playback.
18. EJECT/STOP A/ C button (VCR)
• When the unit is in stop mode, press to remove the cassette
tape from the cassette compartment.
• Press to stop cassette tape playback or recording.
• Press to stop the proceeding timer recording in VCR.
19. FWD D button (VCR)
• Press to rapidly advance the cassette tape, or view the
picture rapidly in forward during playback (forward search).
20. REW E button (VCR)
• Press to rewind the cassette tape, or to view the picture
rapidly in reverse during playback (rewind search).
1. AC Power Cord
• Connect to a standard AC outlet to supply power to this unit.
• Unplug this cord from the AC outlet to completely shut down
the unit.
2. HDMI OUT jack
• Use an HDMI cable to connect to a display with an HDMI
compatible port.
3. ANTENNA OUT jack
• Use to connect an RF coaxial cable to pass the signal from
the ANTENNA IN to your TV.
4. ANTENNA IN jack
• Use to connect an antenna.
5. AUDIO OUT jacks
• Use to connect a TV monitor, AV receiver or other device
with an RCA audio cable.
6. VIDEO OUT jack
• Use to connect a TV monitor, AV receiver or other device
with an RCA video cable.
7. VIDEO IN jack (L1)
• Use to connect external device with an RCA video cable.
8. AUDIO IN jacks (L1)
• Use to connect external device with an RCA audio cable.
9. S-VIDEO IN jack (L1)
• Use to connect the S-video output of external device with
an S-video cable.
10. COMPONENT VIDEO OUT jacks
• Use to connect a TV monitor with component video inputs
with a component video cable.
11. S-VIDEO OUT jack
• Use to connect the S-video input of a TV monitor, AV receiver
or other device with an S-video cable.
12. AUDIO OUT jacks
• Use to connect a TV monitor, AV receiver or other device
with an RCA audio cable.
13. COAXIAL DIGITAL AUDIO OUT jack
• Use to connect an AV receiver, Dolby Digital decoder or
other device with a coaxial digital input jack with a digital
coaxial cable.
Note
• Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
• This unit does not have the RF modulator.
Caution on using S-video, component, or HDMI
connection for VCR:
• Only the playback audio / video is available with
these connections.