Filter
Top Products
43EN
Disc
Management
Recording
PlaybackIntroduction Connections Basic Setup Editing Function Setup VCR Function Others
TIMER RECORDING
You can program the unit to record up to 12 programs
within a month in advance. Daily or weekly program
recordings are also available.
Before recording, make sure
• Set the clock before setting a timer programming.
• Insert a recordable disc with enough recordable space or
a cassette tape with an erase-protection tab.
Note
• If you have not set the clock yet:
“Manual Clock Setting” menu will appear instead of
the timer programming list at step 1. Continue with
the step 4 in “Manual Clock Setting” on page 30 before
setting a timer programming.
•
Use [s / B] to move the cursor to the left and the
right in “Timer Programming” menu.
•
If a basic recording or one-touch timer recording is in
progress on one component (e.g., VCR) and the timer
recording set for the other component (e.g., DVD) is about
to begin, the unit automatically switches to the
programmed channel for timer recording 2 minutes before
the programmed starting time, and the recording in
progress (for VCR) will be canceled UNLESS their recording
channels are the same. If their recording channels are the
same, the timer recording will start without canceling the
recording currently in progress. In this case, the recording
of the same channel will be made on both DVD and VCR.
•
You cannot make a program whose recording time
exceeds 12 hours.
•
Cancel the timer-standby mode by pressing [TIMER
SET] before operation for either DVD or VCR. When
finished operating, press [TIMER SET] to resume the
timer-standby mode.
•
In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which is
not currently timer-programmed.
Guide to Timer Programming Display
Timer Programming
1/1
THU JAN/01 10:00AMSP (1:00)
JAN/ 2/09 1:00 AM 125-01 SP
Date Start End CH
JAN/02 1:00AM 2:00AM 10
New Program
1
5
3
4
2
1. Title of a Timer Program (Contains date, time, channel,
recording mode of the program)
2. Current date and time
3.
Recording mode and length of the recording
4. Timer program list
5.
Total number of pages and current page (2 pages maximum)
1
Press [TIMER PROG.].
2
Use [K / L] to select “New Program”,
then press [ENTER].
Timer Programming
1/1
THU JAN/01 10:00AM
Date Start End CH
New Program
• If there are 6 or more programs, use
[SKIP j / i] to change pages.
3
Use [K / L] to enter the date, then
press [B].
Date
JAN/02
SP 2 : 00
Start
- - : - -
End
- - : - -
Mode
SP
CH REC To
10 DVD
Daily
MON-SAT
JAN/01
JAN/31
MON-FRI
SAT
FRI
SUN
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
.@/: ABC
GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO
TIMER
PROG.
DISC MENU
CLEAR RETURN
TOP MENU
WXYZ
JKL MNO
DEF
ENTER
INSTANT
SKIP
PLAY
DVDVCR
PAUSE
REV
SKIP
STOP
SKIP
FWD
1.3x/0.8x
PLAY
TIME SLIP
TIMER SE ZOOMSEARCHREPEAT
RECREC MODEDUBBING
CH
ENTER
GHI
PQRS TUV
SPACE
WXYZ
JKL MNO
.@/: ABC DEF
SETUP
SKIPSKIP
TIMER
PROG.
TIMER SE
T
Instructions continue on the next page.