Filter
Top Products
PAGE 52
Reference: Detailed Information For Making A Master TV
IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...
To set up a master TV you will need to know how to
enter the L20V54S Installer menu and make changes to
the default values as required. If necessary, familiarize
yourself with the L20V54S Installer menu and how to
make and save changes in the menu, bef
ore attempting to clone the
L20V54S Master TV setup.
You will also need an Installer remote control similar to the one
shown in the front of this manual.
Finally, the TV’s clonable features need to be set up. This is a
critical step. If the Master TV display panel’s clonable features like
adding channel icons or channel labels are not correctly added, then
the cloned L20V54Ss TVs will all have problems.
As the cloning procedure is being performed, specific steps need to
be done at the indicated times to achieve the desired result. Be sure
to do each task as indicated. If a procedure or step is left out or not
performed completely, cloning may not work. At each step, pay
attention to assure the TV screen shows the proper message when
cloning. If the message indicated does not appear, there is a
problem with that step and cloning may not be successful. Cloning
is only possible when the signal source is an An
alog channel, not a
digital channel.
Making a Master TV
Detailed Instructions
The following describes the procedure for preparing a Master
L20V54S for cloning and the procedure for adding Channel Icons
and/or Labels.
*Note: 1: Disconnect all Aux inputs. Under certain conditions, Auto Program
Scan is disabled if there is an Aux input active.
1. Enter the L20V54S installer menu.
a. Reset the internal controller to factory default by accessing
installer menu item 117 FACT DEFAULT, set it to 1 and press
“ENTER”. The value will change back to 0 after the TV’s internal
controller has been restored to factory default condition.
b. Within the Installer menu, set the Installer menu items to the
configuration required of your institution.
c. It is important to set the tuning band at this time, see
Installer menu item 03 BAND/AFC.
d. Set Installer menu item 28 – CH OVERIDE to 001 to allow
access to the Auto Program and Channel List/Channel Label
features in the Channel Menu. Exit the Installer menu.
2. Access the Master TV menus and set the clonable options on the
menus to the desired configuration. Refer to the Clonable Menu
Features Chart on see page 52.
3. Run Auto Program.
4. Enter the Channel List/Channel Label menu and edit the channel
line-up to include the Free-To-Guest Channels only.
5. Assign ICONs to the channels using the Channel Label Menu.
*Note:
You can add Channel ICONS typically network logos like ABC, NBC,
PBS etc. in this step. Or, in Step 7, add Channel ICONS or labels for
channels without Icons.
6. Transfer the TV setup: Enter the L20V54S installer menu.
Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to
the L20V54S. Once the transfer is complete, the system will exit
the Installer menu.
*Note: Only do 2-5-5 + MENU once. The TV setup may be corrupted if
255 + Menu is done more than one time.
7. Edit/Add Channel ICONs and Channel Labels as needed.
Enter Installer menu. With menu displayed, press 2-5-4 + MENU.
See page 50 for detailed instructions:
- Editing/Adding Channel ICON and Labels on Master TV
- Changing a Channel’s ICON on Master TV
- Changing/Adding Channel Labels on Master TV
- Changing Source Labels on Master TV
8. Verify Master TV setup and feature configuration:
• Did you add Channel ICONS?
• Did you add Channel Labels?
• Did you add Aux Source Labels?
• Did you adjust all TV menu options as required?
The TV master setup is now ready to be cloned. Go to the master
TV cloning section or continue on to page 53.