Filter
Top Products
E-39
RECORDING
– Audio dubbing –
For tapes recorded in the 32kHz audio mode, audio dubbing can be performed on the CH3 and
CH4 channel after the recording. (After-recording)
Notes
• For tapes recorded in the 48kHz audio mode, audio dubbing cannot be performed.
• Audio dubbing cannot be performed for DV input signals.
A.DUB
F. REV
INDEX– INDEX+
PLAY
STOP
REMOTE CONTROL UNIT
RM-G3000
REW FF
PAUSE
REC
F. ADV
1. 4.
PLAY
button
2. 3.
PAUSE button
5.
STOP
button
3.
A.DUB
button
Mini
PROFESSIONAL
SET
MENIU
EJECT
REC PLAY
PAUSE
REW
STOP
FF
DVCAM NTSC
PA L
REC INH.
CH-1/3
CH-2/4
BR-DV3000
A.DUB
OPERATE
INPUT SEL.REMOTE SEL.
MIC
SERIAL
WIRELESS
9PIN
LINE
DV
Y/C
2. 3.
PAUSE
button
5.
STOP buttonINPUT SEL. switch
1. 4.
PLAY button
3.
A.DUB button
MIC
terminal
Connection
Audio dubbing sounds are input from the AUDIO IN
terminal on the rear panel or the MIC terminal on
the front panel. MIC terminal prevail over the AU-
DIO IN terminal.
Setting
• Set the AUDIO item of the AUDIO/VIDEO menu
to “32K”.
• Do not set the INPUT SEL. switch on the front
panel to “DV”.
Operation
1.
Press the PLAY button to play the tape.
2.
At the position where you want to au-
dio dub, press the PAUSE button.
¥ The unit goes into the STILL mode.
3.
Hold down the PAUSE button and press
the A.DUB button.
¥ The unit goes into the audio dubbing pause
mode.
4.
Press the PLAY button.
¥ Audio dubbing begins. Audio signals are
recorded on the CH3 and CH4 channel.
Ⅵ To stop audio dubbing temporarily, press
the PAUSE button.
5.
To end audio dubbing, press the STOP
button.
Memo
• During audio dubbing, if the tape comes to a
part recorded in a non dubbing-feasible mode
(such as LP mode or 48kHz audio mode), the
VTR will enter the STOP mode. When this hap-
pens, high-volume noise from the DV output
will occur. Hence, before audio-dubbing,
please check the recording mode of the tape.
• In the case that a microphone is connected to
the MIC terminal, sound output from this ter-
minal will be recorded. In the absence of MIC
input, signals from the CH1/3, CH2/4 AUDIO
IN terminal on the rear panel will be recorded.
• When audio dubbing cannot be performed, an
alarm message will be displayed on the moni-
tor. (
☞
Page 23)
• Audio dubbing PAUSE cannot be executed di-
rectly in the STOP mode. Please execute it in
the STILL mode.
During audio dubbing pause, sound from the
CH3/CH4 channel is output via the monitor
but sound output from the DV terminal is not
possible.
• If audio dubbing is repeated on a short sec-
tion of the tape, noise may occur for an in-
stant when the section is played.
• During audio dubbing, noise may be produced
on the playback video or EE sound but the
recording is normal.
• The playback sound of CH1/2 cannot be re-
corded on CH3/4 (sound on sound).
• During backspace operation of audio dubbing,
audio dubbing cannot be performed on unre-
corded parts.
• When audio dubbing is performed on tapes
recorded on other devices, it may not record
correctly. Please record with this unit before
performing audio dubbing.