Filter
Top Products
Masterpage:Right+
EN 53
Filename [DR-MV1SU_07VCR Operation.fm]
Page 53 February 23, 2004 4:29 pm
OPERATIONS ON VCR DECK
You can program this unit to timer-record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer-record the program.
1 Load a cassette with the record safety tab intact.
2 Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
3 Press PROG/CHECK to access the
Program Check screen.
4 Press rt to select the blank
number, then press ENTER. The
program screen appears.
5 Press we to select “START”, then
press rt to set the desired start time.
● Each press of rt advances/goes back
the start time in 1-min. increments.
● To advance/go back the start time in 30-
min. increments, press and hold rt.
6 Press we to select “STOP”, then press rt to set the desired
stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
7 Press we to select “DATE”, then press rt to set the desired
date.
● The current date appears on the TV screen. The date you enter
appears in its place.
8 Press we to select “CH”, then press rt to select the desired
channel.
9 Press REC MODE to select the desired recording mode. Or
press we to select “SP/EP”, then press rt to select the desired
recording mode.
10 Press ENTER to access the Program Check screen.
11 Press PROG/CHECK to complete timer programing.
“PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears. If “PROGRAM NOT
COMPLETED PROGRAM OVERLAP” appears on the TV screen,
see page 54.
● To program another timer, repeat steps 3 – 11.
12 Press VCR TIMER (#) to engage the unit’s timer mode. The
VCR timer lamp lights up on the unit and the DVD deck is
automatically selected. When the DVD deck is in timer standby
mode, the unit is automatically turned off.
● To disengage the timer mode, press VCR TIMER (#) again.
NOTES:
● To Timer-Record Weekly Or Daily Serials:
— anytime during steps 7 through 9, press number key “9” for
weekly serials or number key “8” for daily serials (Monday – Friday).
Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
● You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, “PROGRAM FULL”
appears on the TV screen. To record the extra program, you must
first cancel any unnecessary programs. (
੬ pg. 54)
● In case of a power failure after programing, the unit’s memory backup
keeps your selections for approximately 5 seconds.
● Programs that start after midnight must have the next day’s date.
● To record the programs received by cable box or DBS receiver,
record on the DVD discs. For details, refer to “Manual Timer
Programing” (
੬ pg. 42).
Manual Timer Programing
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
ENTER
VCR TIMER (#)
rtw e
VCR/DVD
0 – 9
REC MODE
(PROG/CHECK) TO NEXT
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4
5
6
7
8
PROGRAM 4
START STOP
– –:– –AM – –:– –AM
DATE CH SP/EP
– –/– –/– – – – – SP
PRESS (RTYU, 8=DAILY
9=WEEKLY), THEN (ENTER)
(PROG/CHECK) TO END
DR-MV1SU_00.book Page 53 Tuesday, February 24, 2004 12:53 PM