JVC SP-PWV70 DVD Player User Manual


 
66
IMPORTANT:
When using the remote control, check to see if
its remote control mode selector is set to the
correct position:
To operate this system, set it to AUDIO/TV/
VCR.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
cancelled before you finish, start from step 1 again.
When selecting DVD, AUX, or AUX DIGITAL as the source, the
settings of the corresponding items in the choice menus also
change.
From the remote control ONLY:
1 Press SETTING.
The item you last selected appears on the display
window.
Example: “BAL” has been selected.
2 Press Cursor /5 repeatedly to select the
item you want to set.
Each time you press the button, the items shown on the
display window change as follows:
BAL BASS TREBLE FRNT SP
CNTR SP REAR SP FRNT D CNTR D
REAR D CROSS LFE ATT. D.COMP
(back to the beginning)
CHANNEL VOLUMETV VOL
TUNING
FF/
/REW
TV/VIDEO
1
MUTING
¡
PLAY
DOWN UP
CENTER
+
REAR-R
+
TEST
SLEEP
TV
VCR
SETTING
TV RETURN
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUND
MODE
FM MODE
123
456
789
10
0
+10
100+
CATV/DBS
REAR-L
+
SETTING
button
Cursor and
ENTER buttons
L
R
See the corresponding pages for the detail of adjustments.
BAL (Balance):
Adjust the balance between the left and right front
speakers. (See page 59.)
BASS, TREBLE:
Adjust the enhancement level for bass or treble sound
from the front speakers. (See page 59.)
FRNT SP (front speakers),
CNTR SP (center speaker),
REAR SP (rear speakers):
Select the size of each speaker. (See page 60.)
FRNT D (front speakers distance),
CNTR D (center speaker distance),
REAR D (rear speakers distance):
Set the distance from the listening position to the
speakers. (See page 61.)
CROSS (CROSS OVER):
Select the cutoff frequency of the subwoofer according
to the front speakers used with this system.
(See page 60.)
LFE ATT.:
Diminish the distortion of the bass sound from the
subwoofer while playing back a disc with Dolby Digital
or DTS Digital Surround. (See page 59.)
D.COMP (D. RANGE COMPRESSION):
Enjoy a powerful sound at night even at a low volume
level when listening to the sound with Dolby Digital.
(See page 59.)
3 Press Cursor 2/3 to make an adjustment.
Example:
BAL:
“L–21” to “L–1” “CENTER” “R–1” to “R–21”
BASS, TREBLE:
Within the range between –10 to +10 (by 2 step)
FRNT SP, CNTR SP, REAR SP:
“SML” (small) “LRG” (large) “NO” (none)
(“NO” is not selectable for the front speakers.)
FRNT D, CNTR D, REAR D:
Within the range between 0.3 m and 9.0 m. (by 0.3 m
step)
CROSS:
“200 Hz” “150 Hz” “120 Hz” “100 Hz”
“80 Hz”
LFE ATT.:
“ON” “OFF”
D.COMP:
“MID” “MAX” “OFF”
4 Repeat steps 2 and 3 to set other items.
NOTES:
If you have selected SML for the front speakers, you cannot select
LRG for the center and rear speakers.
You can confirm your adjustment of speaker settings by listening to
the test tone. To output the test tone, press SOUND, then TEST.
(See page 35.)
L
R
Setting the system through the display window
You can adjust the sound and speaker settings of this system through the display window.
You can adjust the sound setting of front speakers (“BAL,” “BASS,” and “TREBLE”) for each source.
The adjustments of the speaker size, speaker distance, “LFE ATT,” “CROSS,” and “D. COMP” take effect for all sources.
AUDIO/
TV/VCR
CATV/DBS
EN55-66TH-V70[A]1 02.4.9, 10:18 AM66