Filter
Top Products
PAGE 36
Detailed Descriptions of Installer Menu Items
000 - INSTALLER SEQUENCE
Specifies entry sequence to the Installer Menu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff. The POWER
MANAGE function is for saving energy. If set to 0, Power Manage is Off.
Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the
unit will remain On, unless there has been activity from either the
control panel or remote control.
002 - AC ON (AC Power Switchable)
If set to 1, allows the TV to turn On just by applying AC power.
Pressing the On button is not necessary. This is desirable if the TV is
plugged into a cable box or a power outlet controlled by a wall switch.
Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is
Off, and 1 is On.
NOTE: If set to 1 (On), the TV does not respond to On/Off commands
from either the remote or the display control panel, and the SLEEP
TIMER is also nonfunctional.
003 - BAND/AFC (Band/Automatic Frequency Control)
There are 4 possible settings for this option:
0 = Broadcast 1 = CATV
2 = HRC 3 = IRC
If some channels were not found by Auto Tuning (Channel Search),
select the appropriate Band setting here and add the channels using
the Channel Edit option in the Channel Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial channel
number when the TV is turned On. This feature is useful for an in-
house information channel, since the TV would always select that
channel when it is turned On. Setting this to 255 causes the last
channel viewed when the TV was turned Off, to be the tuned to chan-
nel when the TV is turned On again. Note: For a digital Start Channel,
always remember to set item 104 to the Minor Start Channel number.
255 = Last channel 1 ~ 125 = Ch X 0 = Aux
126 Map to Channel 3. 127 Map to Channel 4.
005 - CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if the system must always be on the same channel.
Changing channels with Channel Up/Down or keypad numbers is impos-
sible. Channel Lock is inactive if set to 0 (default).
Generally, this feature is used in connection with START CHANNEL
(Installer item 004) where the start channel may, for example, be set
to 3 or 4. If the start channel is 3, then the TV will remain locked on
Channel 3.
NOTE: For Items 007, 008 and 009
For legacy reasons, the scale used is 0 - 63. The PTC software will
translate this to the 0 - 100 scale used by the TV.
To translate a TV volume level to the installer menu value, use the fol-
lowing formula:
Installer Value = TV V
alue x 63
100
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume level
setting when the TV is turned On. This feature is useful for an in-house
information channel, since the TV would always select that volume
level when it is turned On. The range of values are 0 - 63, 255. If 255
is selected, the current volume level will be retained in memory when
the TV is turned Off; at turn On, the volume level will be automatically
set at the previous or last level.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable with the
VOLUME (VOL) Up/Down control. In this way, for example, someone
cannot set the volume too low to hear. The value range is from 0 to 63
— change values with ADJ Left/Right arrow. The factory default is 0,
which provides the full range of volume control, if item 009 MAX VOL-
UME is also set to 63. It may be best to set the same value on every
TV.
NOTE: The minimum volume level cannot have a value setting higher
than the MAX VOLUME level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable with the
VOLUME (VOL) Up/Down controls. In this way, for example, someone
can not set the volume level high enough to disturb others. The value
range is 0 to 63, with 63 as the default, which gives the user the full
range of volume control, if item 008 MIN VOLUME is also set at 0.
Change values with ADJ Left/Right arrow keys. It may be best to set
the same value on every TV.
NOTE: The maximum volume level cannot have a value setting lower
than the MIN VOLUME level (described previously).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot be
muted. If set to 0, sound can be muted.
206-4071
Installer Menu