LG Electronics 32-3DCH-UA CRT Television User Manual


 
206-4071
PAGE 39
thus relaxing M.P.I. timing requirements to be compatible with PC
based Windows controlled systems, range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time]).
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent by
disabling the blocking hours function.
Set to 1 to install Parental Control restrictions permanently.
Set to 0 for user-specified hours control of blocking schemes.
087 - REAR RGB EN. (Rear RGB Enable)
Controls access to rear RGB input on TV.
Set to 0 to disable RGB input.
Set to 2 to enable for RGB PC input and automatically configure its
input format every time TV is turned On.
Set to 18 to enable RGB PC input and to configure the input format
one time only with AC power cord removal and reinsertion.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
090 - KEY LOCK
If set to 1, front keyboard buttons Channel, Volume and Captions are
disabled, Power button remains enabled. If set to 0, front keyboard
Channel, Volume, Captions and Power buttons are all enabled.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function menu, if Function menu is
available.
Set to 0 to disable SAP feature on Function menu, if Function menu is
available.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up, see settings below.
Note: Only applies if item 106 Aspect Ratio Lock is disabled, set to 0.
Set to 0 “Set By System”.
Set to 1 for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 4 for Zoom 1
Set to 5 for Zoom 2
099 - BACK LIGHTING
Sets the TV screen brightness at power up, see settings below.
Default setting is 100.
1 - 100 Static Backlighting.
(1 = Dimmest picture, 100 = Brightest picture.)
101 - 200 Dynamic Backlighting.
(101 = Dimmest picture, 200 = Brightest picture.) If settings are above
200, the TV automatically controls backlighting depending upon the
picture level of the current program.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.
103 - ATSC TUNE MODE
Sets ATSC tuning mode: Default set to 1 for Physical channel scan.
Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets XX-XX digital minor sub start channel at power up: 0=NTSC. If not
0, number selected is the digital minor start channel number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power Off.
Set to 0 to retain default aspect ratio with power Off. See item 96
Default Aspect Ratio above.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for normal.
Set to 1 for blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal.
Set to 1 and press Enter to load presets for all of the Installer menu
item settings.
WARNING: Setting this to 1 and pressing Enter will reload
the factory defaults and clear the channel list including
erasing any assigned Channel Icons and custom channel
Labels.
118 - POWER SAVING
Default is set to 1, power saving mode is enabled.
Set to 0 to disable power saving mode.
• Power Saving is only active when TV is in standby mode.
• Power Saving is not available in normal power on mode.
If Power Saving is enabled and TV is in Standby mode with External
card installed: TV can supply 12V (9.6 Watts) to External card and
Standby power consumption will be small.
If Power Saving is disabled and TV is in Standby mode with
External card installed: TV can supply 12V (12 Watts) to External card
and Standby power consumption will be normal.
Installer Menu