Filter
Top Products
11
ENGLISH
CONFIGURING YOUR REMOTE TO
CONTROL OTHER DEVICES
The TV and Amp devices on the Music Server remote
control may be individually configured to control a range of
televisions and amplifiers from well known manufacturers.
To configure the remote to control your
television
• Press the TV and Pbuttons simultaneously;
hold them down for 1 second.
The TV button will remain lit for 20 seconds; the
configuration process must be completed during this time.
• Enter the 3 digit numeric code matching the
manufacturer of your television from the list in
Appendix A.
• Press the TV button again.
The TV button will blink twice to indicate that the
configuration has been accepted. If the TV button does not
blink begin the process again, taking care to enter the
number exactly as printed in the list. If the television is
switched on during the configuration process, entering the
correct code will cause the television to go into standby.
To configure the remote to control your
amplifier.
• Press the Amp and Pbuttons simultaneously;
hold them down for 1 second.
The Amp button will remain lit for 20 seconds; the
configuration process must be completed during this time.
• Enter the 3 digit numeric code matching the
manufacturer of your amplifier from the list in
Appendix A.
• Press the Amp button again.
The Amp button will blink twice to indicate that the
configuration has been accepted. If the Amp button does
not blink begin the process again, taking care to enter the
number exactly as printed in the list. If the amplifier is
switched on during the configuration process, entering the
correct code will cause the amplifier to go into standby.
Reassigning volume control when using the
Music Server.
If the volume setting of the Music Server is set to fixed the
Nand OMute keys will do nothing (for more information
on volume output settings see the chapter called Advanced
Settings p.25.). These buttons may therefore be
configured to control the volume on your amplifier whilst the
HDD Audio device is selected. To re-configure these keys:
• Ensure that the Amp device is correctly configured
to control your amplifier (as shown above).
• Press the HDD Audio and Pbuttons
simultaneously; hold them down for 1 second.
The HDD Audio button will remain lit for 20 seconds; the
configuration process must be completed during this time.
• Press the O Mute
• Press the N+ key
• Press the Amp device key
The HDD Audio device key will blink twice to indicate that
the configuration has been accepted. If the HDD Audio
button does not blink begin the process again, taking care
to press the buttons in the correct sequence. The Nand
O
Mute keys should now control the amplifier when the
HDD Audio device is selected.
To return the N and O
Mute keys to their original
configuration repeat the above process, pressing the HDD
Audio button instead of the Amp button.
Note: The HDD Audio button always uses a device
number of 000. You should never need to change this for
normal operation.
CONNECTING YOUR MUSIC SERVER
Note: Do not make any connections to the Music Server
while the power supply is connected and switched on.
• Connect the supplied telephone lead to a standard
analogue telephone socket. Connect the other end
of this cable to the socket marked Modem on the
back panel of the Music Server.
• Connect the red plug of the supplied audio lead to
the red Analogue Audio Out 1 socket on the back
of the Music Server. Connect the adjacent white
plug to the white Analogue Audio Out 1 socket on
the Music Server. Connect the other end of this
cable to the AUX or CD inputs on your amplifier.
• Connect the yellow plug of the supplied TV lead to
the yellow Video 1 Out socket of the Music Server.
For the European TV lead* connect the Scart plug
to the ext. 1 or 2 socket on the rear of your TV. For
the non-European TV lead connect the yellow plug
to the video input on the rear of your TV.
• Connect the supplied power cord to your mains
power supply.
• Switch on your television. Select the appropriate
video channel to view the Music Server TV User
Interface display.
* For Scart connection, the red and black plugs are not
required.
SWITCHING ON AND OFF
There are two power saving modes available from the
POWER/Standby button on the Music Server front panel
and the Lbutton on the remote control.
If you are not using your Music Server it is strongly
recommended that you place the unit into one of the two
power saving modes.
Standby mode
Standby mode should be used when the Music Server is
not being used for a short period of time. Putting the unit
into standby takes just a few seconds; switching the unit on
from standby also takes just a few seconds. Do not
remove the power from the Music Server in this mode.
Off mode
Off mode should be used when the Music Server is not
being used overnight (or for several days). There is a short
wait whilst the unit is switched to off mode; switching the
unit on from off mode may take a few minutes. When the
unit is in off mode it consumes very little power. You can
safely remove the power from the Music Server in this
mode.